Manual Haas-Sohn HSP1.17 (page 5 of 31) (English)

812047

Zoom out

Zoom in

1/31

Floor protection

The floor is to be protected from the radiant heat from

the area of the viewing window (combustion chamber).

In addition, for practical reasons associated with

cleaning it is recommended that you install your pellet

stove on a fireproof base that extends beyond the device

at the back and on the sides by at least 5 cm and at the

front by at least 50 cm. We have floor protection plates

(underlay plates or U plates) in our range of accessories.

If required, you may order them from your specialist

stove dealer. As an alternative, a tile or stone floor is of

course very suitable.

Safety gaps (minimum gaps):

During installation of the stove it is absolutely essential

to observe the official fire protection regulations. Ask

your district heating inspector about this.

The following must be maintained as the minimum

distances from flammable or temperature-sensitive

materials (e.g. furniture, wallpaper, wooden cladding)

and from loadbearing walls. (See drawing):

A 5 cm from the back wall

B 10 cm from the side walls and

C 80 cm in the direction of radiation.

Figure 2: Safety gaps

The chimney (fireplace or flue) must for example be

made of stainless steel or ceramics (glazed internally) so

that it cannot rot. This is necessary because of the low

temperature of flue gases from your pellet stove.

Standard trade flue tubes may be used for the

connection to the fireplace. Approved Flex steel flues

are also suitable.

Since excess pressure may build up at the smoke outlet

because of the way that the pellet stove works with an

induced draught fan, all fume outlet pipes as far as the

intake to the fireplace must be gas-tight. It is also

essential to ensure that the flue tube does not stick out

into the open cross-section of the chimney. The use of

wall lagging is recommended for the insertion into the

chimney. (See Figure 3).

With longer flue gas pipework, horizontal sections and

constrictions must be avoided and specially insulated

flue tubes should be used. Pipework rising in the

direction of the chimney is recommended.

Figure 3: Chimney connection

1 = Wall lagging

2 = Gas-tight pipework

3 = Underlay plate

External air intake:

In airtight buildings, whilst the pellet stove is operating, a

reduction in the oxygen level in the room where the

stove is installed may occur, so adequate ventilation

must be ensured. For this the pellet stove offers you the

option of operating independently of the air in the room.

To do this, connect the air intake elbow located on the

back (diameter: 57 mm) to a hose or a similar suitable

air duct. The end of the air duct must be located in the

open air or in a well-ventilated room within the building.

When installing the pellet stove in combination with

controlled residential room ventilation, the end of the air

intake duct must not be connected to the ventilation

system in an adjacent room with the air connection

system. To ensure sufficient volume of air intake, the

pipe should not be longer than about 3 m and not have

too many bends. This pipe should have a minimum

diameter of 5 cm. (The bigger, the better). If the pipe

goes to the open air, it must end with a downward 90°

bend or with wind protection. (See Figure 4).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn HSP1.17 in the language / languages: English as an attachment in your email.

The manual is 5.65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn HSP1.17

Haas-Sohn HSP1.17 User Manual - German - 32 pages

Haas-Sohn HSP1.17 User Manual - French - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Haas-Sohn HSP1.17 Manual

Product: