812047
4
Zoom out
Zoom in
Previous page
1/31
Next page
4
The pellet stove may not be installed in the open
air!
Attention! The mains cable plug must remain freely
accessible after installation.
The pellet stove may only be operated with standard
wood pellets (6 mm diameter). (See Section 7.1
“Fuel”).
The protective grille located in the pellet container
must not be removed.
Attention! The Pelletto stove may only be
operated with the tank cover closed.
Placing non-heat-resistant materials or objects on
the stove or within the specified minimum distances
is forbidden. Here please note in particular that
during Standby” operating status, the stove may
unexpectedly and unintentionally start heating when
the room temperature falls below the desired
temperature.
Never use liquid fuels to ignite the pellet stove or to
revive existing embers.
With the burning up of fuels, heat energy is
released, leading to strong heating of the heating
device’s surfaces (e.g. doors, door and control
handles, viewing window panels, side walls, front
wall, flue tubes). Touching these parts without
suitable heat protection gloves or a tool is to be
avoided!
The device ignites by itself in “Standby” mode.
Because of the heat generated on the panel, make
sure that no-one who is unfamiliar with the operation
of the pellet stove is unsupervised in the room where
it is installed.
Bring these risks to your children’s and guests
attention!
In particular, any cleaning staff should be informed
and instructed regarding the possible unexpected
heating up of the stove.
Placing non-heat-resistant objects on or near the
heating device (even when it is cold, since it can
ignite again by itself) is forbidden!
Do not lay any laundry on the stove to dry!
Clotheshorses for drying clothes and the like must
be positioned at sufficient distance from the heating
device fire risk!
When operating your heating device, it is forbidden
to work with highly flammable or explosive
substances in the same room or an adjacent one!
3. Installation of the pellet stove and connection to
the chimney
The packaging on your new pellet stove gives it optimum
protection against damage. Nevertheless, damage may
have occurred to the stove or to accessories in transit.
Please therefore check your stove after unpacking for
damage and completeness! Report any defects or
anything missing to your specialist stove dealer without
delay!
The packaging on your stove is by and large
environmentally neutral. The timber packaging is not
untreated. The timber, the cardboard and the films can
be taken without problems to your local recycling centre.
For the correct operation of your pellet stove it is
important that it stands horizontally.
The room temperature sensor that is located on the back
wall has a length of about 1.5 m and should be
positioned hanging free at the back.
Figure 1: Back connections
1 = Mains electricity socket
2 = OC overheat cutout
3 = Room temperature sensor
4 = Fume elbow 80 mm
5 = Outside air connection 40 mm
6 = Bottom of back wall
6
1
3
5
2
4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn HSP1.17 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn HSP1.17 in the language / languages: English as an attachment in your email.

The manual is 5.65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn HSP1.17

Haas-Sohn HSP1.17 User Manual - German - 32 pages

Haas-Sohn HSP1.17 User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info