812045
25
Zoom out
Zoom in
Previous page
1/32
Next page
GB
21
F0006 A. Combustion chamber door open during
operation
B. Damper in front of the door contact switch
not in the right position
C. Cable broken in the electric wiring to the
door contact switch
D. The connector has come out on the door
contact switch or on the central unit
A. Clean burner - close door
B. Clean burner - Adjust damper in front of the
door contact switch
C. Cable broken on door contact switch -
contact service department
D. Contact service department
F0007 A. Flue gas temperature sensor defective or
not connected
A. Contact service department
F0008 A. Flue gas temperature sensor defective A. Contact service department
F0009 A. Note: Combustion chamber door open
during "Off or standby"
A. No correction necessary - Close door -
Error is automatically cleared
F0011 A. Room temperature sensor defective or not
connected
A. Contact service department
F0012 A. Room temperature sensor defective A. Contact service department
F0015 A. Induced draught fan defective
B. Power supply to the fan motor interrupted
A. Contact service department
B. Check cable - contact service department
F0018 A. Power cut A. Clean burner - Clear error 018
F0021 A. Burner dirty
B. Pellet tank empty
C. Downpipe / screw conveyor blocked
D. Room too airtight required combustion air
cannot flow into the room
E. Flue gas temperature sensor defective
F. Screw motor defective
G. Pellet fuel has too low a calorific value
A. Clean burner
B. Clean burner - fill pellet tank
C. Clean the intake on the screw conveyor
housing with a vacuum cleaner. Clean
burner
D. Clean burner - Ensure adequate
combustion air
E. Flue gas temperature sensor defective -
contact service department
F. Screw motor defective - contact service
department
G. Clean burner - switch to high quality pellet
type
F0022 A. Flue draught too low
B. Flue draught too high
C. Burner dirty
D. Flue tube pipeline too long (horizontal)
E. Flue gas temperature sensor defective
A. Measure flue draught - contact service
department
B. Measure flue draught - contact service
department
C. Clean burner
D. Change flue tube pipeline- contact service
department
E. Flue gas temperature sensor defective -
contact service engineer
F0023 A. Flame temperature sensor defective or not
connected
A. Contact service department
F0024 A. Flame temperature sensor at bottom
defective or not connected
A. Contact service department
F0026 A. Pellet tank empty
B. Burner not lying flush
C. Burner dirty
D. Pellet fuel has too low a calorific value
E. Downpipe / screw conveyor blocked
F. Room too airtight required combustion air
cannot flow into the room
G. Flame temperature sensor defective
A. Fill pellet tank
B. Position burner correctly
C. Check burner/ clean burner
D. Switch to high quality pellet type
E. Clean the intake on the screw conveyor
housing with a vacuum cleaner.
F. Ensure adequate combustion air - Connect
stove with outside air
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn HSP 8 HOME at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn HSP 8 HOME in the language / languages: English as an attachment in your email.

The manual is 1.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn HSP 8 HOME

Haas-Sohn HSP 8 HOME User Manual - German - 32 pages

Haas-Sohn HSP 8 HOME User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info