Manual Haas-Sohn COMPACT-PELLET 310 (page 9 of 40) (English)

812036

Zoom out

Zoom in

1/40

The duration of this procedure is approx. 2

minutes.

The values thereby measured are the basis

for whether or not the device can continue its

operation and which LED’s light up for the

„optical visualization of the burner soiling“.

5.5. Cooling

If the set target room temperature is reached,

i.e. actual room temperature and target room

temperature match, then the controller

switches over to the operating state „Cooling“.

The conveying of the fuel is terminated, i.e.

the screw conveyor which is located in the

worm tube stops, the speed of the induced

draught blower is regulated to a precisely

defined speed and the fuel, which is still in the

burner tray, is burned.

The convection air blower is regulated to a

precisely defined speed.

The cooling phase is limited time-controlled.

(duration approx. 15 minutes)

After completion of the operating state

„Cooling“, the device switches to the

operating state „Standby“.

5.6. Standby

In this operating state, no combustion

operation takes place, all components,

induced draught blower, convection air blower

and screw conveyor are stationary, the

ignition is switched off, the device is in

„Standby position“.

Before the stove can switch from the

operating state „Standby“ to the operating

state „Start phase“ again, two starting

conditions must be fulfilled:

1. The set target room temperature must

be undershot by at least 1.0 °C

2. The waste gas temperature measured

with the waste-gas temperature sensor

must be less than 70 °C

Only when both starting conditions are

fulfilled does the device switch from the

operating state „Standby“ back to the

operating state „Start phase“.

Attention!

In „Standby-mode“ the device starts

automatically. Due to the development of

heat on the panel, it must be ensured, that

no unsupervised persons who are not

familiar with the operation of the pellet

stove remain in the room of installation.

The placing of non-heat-resistant

materials and objects on the stove and

within the prescribed minimum distances

is forbidden.

5.7. Safety shutdown

If a fault occurs, regardless in which operating

state and during which mode, then a safety

shutdown is initiated.

The sequence of the safety shutdown is

precisely defined.

During the safety shutdown, the components

are switched as follows:

Induced draught blower – ON

Convection air blower - ON

Screw conveyor – OFF

Ignition – OFF

The end of the safety shutdown is

temperature-dependent, i.e. the operating

state „Safety shutdown“ is retained so long

until the stove has cooled to a waste-gas

temperature of less than 80 °C.

After conclusion of the safety shutdown, the

controller switches over to the operating state

„Fault“.

5.8. Fault

The stove can no longer be operated

automatically.

The operator can read off the fault on the

display.

After proper remedy of the fault and

acknowledgement of the error message on

the control unit, the stove can be set into

operation again.

5.9. Shutdown – Operating State OFF

Method of procedure:

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn COMPACT-PELLET 310 in the language / languages: English as an attachment in your email.

The manual is 3.71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn COMPACT-PELLET 310

Haas-Sohn COMPACT-PELLET 310 User Manual - German - 43 pages

Haas-Sohn COMPACT-PELLET 310 User Manual - French - 40 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Haas-Sohn COMPACT-PELLET 310 Manual

Product: