812035
14
Zoom out
Zoom in
Previous page
1/40
Next page
14
content, different lengths. Precise quality features
can however only be determined with suitable
technical analysis equipment.
A simple quality test: Put a few pellets in a glass
of water:
Good quality: Pellets sink
Poor quality: Pellets float.
The use of poor quality or impermissible fuel
impairs the function of your pellet stove and in
addition can lead to the expiry of the guarantee
and the thereby associated product liability.
Impermissible fuels are e.g. also chippings, straw
or maize. The burning of wood pellets of poor
quality leads to the cleaning intervals becoming
shorter and more fuel being consumed, as a
result however the pellet tank must also be filled
more frequently.
Wood pellets are packed in plastic- or paper
sacks. To ensure trouble-free burning of the wood
pellets it is necessary to transport and store the
fuel as dry as possible and free of dirt. When in
contact with moisture, the pellets swell up greatly.
Take care when filling wood pellets in the storage
container that the pellet sacks do not come into
contact with the hot surfaces of the stove.
Two kilograms of wood pellets have about the
same energy content as one liter of „Heating Oil
Extra Light“. Observed 3-dimensionally, 3 m3 of
wood pellets corresponds to approx. 1,000 liters
of heating oil. Different heating outputs of the
pellet stove are not only caused by the quality of
the pellets, but also by the raw material wood
(type of wood).
7.2. First commissioning of your pellet stove
The materials of the pellet stove must slowly get
used to the development of heat. Through careful
heating you avoid cracks in the furnace plates,
enamel damage and material distortion. Therefore
do not set the target temperature on the control
unit too high (about 1.5°C to 2°C higher than the
momentary room temperature).
Before the first commissioning, possibly
existing stickers are to be removed as well as
all accessory parts withdrawn from the ash
tray, respectively the furnace, this also applies
to possibly existing transport safety devices.
Please check, whether the furnace lining is
engaged in its anchoring (this could have
slipped out of its position through transport or
during the installation of the stove).
Check whether the burner pot is fitting
perfectly in its mounting.
Close the furnace door.
Fill the storage container with standardized
pellets (Ø 6 mm).
Plug in mains cable
Set the On/Off toggle switch to „1“.
After the toggle switch is set to ON, the
controller begins with the initialization. This
procedure takes a few seconds.
After the initialization, the information page
appears – press right key (menu) – set cursor
to operating mode – press right key (select) –
select the required mode of operation with the
cursor – press right key (Save)
Stove starts with the burner test – duration
approx. 2 minutes – measurement of the
burner soiling.
After the burner test, the start phase begins.
Tip!!
For the first commissioning, place approx. 30
pellets on the burner. This accelerates the starting
operation.
General:
If the start phase could not be successfully
concluded, i.e. no development of flames or the
required temperature on the temperature sensor
not reached, than a safety shutdown is initiated
and an error message tripped („Start phase
waste-gas target temp. not reached – check
burner – Date and Time“).
Remedying the fault:
After the stove has cooled down, the burner is to
be emptied and if necessary cleaned. Caution!
There may still be glowing cinders in the ash!
Then press the left key on the control unit
continuously until the fault message appears –
then press the right key of the control unit (Ack.)
– the information page now appears – press right
key (menu) – set cursor to operating mode and
press right key (select) – that page appears in
which the operating mode can be selected –
select required operating mode with the cursor
and press right key (Save) – the stove begins
with the burner test (duration approx. 2 minutes)
and then the start phase is initiated.
Note: A possible smell developing due to the
burning-in of the protective enameling disappears
after a short time. Please ventilate the installation
room well. The enameling does not however
contain any toxic vapors.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn COMPACT-PELLET 309 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn COMPACT-PELLET 309 in the language / languages: English as an attachment in your email.

The manual is 3.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn COMPACT-PELLET 309

Haas-Sohn COMPACT-PELLET 309 User Manual - German - 43 pages

Haas-Sohn COMPACT-PELLET 309 User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info