564788
18
Zoom out
Zoom in
Previous page
1/34
Next page
18
Here the ACTUAL flame temperature is compared
with the TARGET in combination with the processor-
regulated control unit and the appropriate combustion
air volume required for the combustion of the energy
level in the grate is supplied by means of the induced
draught fan.
9.9. Flue gas thermosensor
The flue gas thermosensor is located on the housing
of the induced draught fan and protrudes into the flue
gas duct across the direction of the flow of the flue
gas, where the flue gas flows around it, and thus
measures its temperature and temperature change.
(See Figure 10+12).
With the thermosensor, the temperature and its
change can be measured directly (accurate to about
2ºC) in the flue gas and so be accessed for the
control unit and regulation.
9.10. Room temperature sensor
The room temperature sensor measures the
ACTUAL room temperature in the area of the
stove.
The room temperature sensor is an instrument for
the TARGET ACTUAL comparison between the
TARGET room temperature and the ACTUAL room
temperature and is therefore the basis for the
specification of the required heat output for the
stove.
9.11. OC Overheat cutout
The overheat cutout sensor is located on the
screw conveyor tube. When a certain temperature
is reached, the OC is triggered independently of the
control unit and it cuts the stove off from the
electricity supply. (Thermo protection).
9.12. Combustion chamber cladding
The combustion chamber is clad on its three
casing surfaces, the left side wall, the right side
wall and the back wall with the material Vermiculite.
Figure 16 : Combustion chamber
1 = Combustion chamber cladding right
2 = Combustion chamber cladding left
3 = Combustion chamber cladding back left
4 = Combustion chamber cladding back right
5 = Flame temperature sensor
6 = Bottom temperature sensor
7 = Pellet chute
8 = Combustion pot
9 = Ash box
10 = Door contact switch
9.13. Flue tube connection
The diameter of the flue elbow is 80 mm. The flue
tube must be connected to the fireplace in
accordance with official regulations. For questions
in connection with this, please contact your local
chimneysweep. Because of the way the pellet
stove works with a combustion air fan, high
pressure is generated at the flue gas outlet and
possibly in the fireplace. This means that the flue
gas pipes must be designed to be gas-tight as far
as their entry into the fireplace.
9.14. Mains cable and master switch
Important! The electricity supply to the pellet stove
must always be present! No time switches or other
electric switches may be inserted in or before the
stove’s mains cable. Otherwise your pellet stove
may suffer damage.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn CATANIA-RLU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn CATANIA-RLU in the language / languages: English as an attachment in your email.

The manual is 2.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn CATANIA-RLU

Haas-Sohn CATANIA-RLU Usermanual and installation guide - German - 34 pages

Haas-Sohn CATANIA-RLU User Manual - Dutch - 33 pages

Haas-Sohn CATANIA-RLU User Manual - French - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info