665711
65
Zoom out
Zoom in
Previous page
1/88
Next page
65
TIG 220 DC / 300 DC
NL
Deze lasmodus met pulsstroom wisselt sterke lasstroom (l, lasimpuls) af met zwakkere stroomimpulsen (l_Koud, afkoelingsimpulsen van het werks-
tuk). De pulsmodus wordt gebruikt om de las stukken samen te voegen, met een beperkte temperatuur stijging.
Voorbeeld :
De lasstroom l is afgesteld op 100A en %(l_koud) = 50%, dus : een Koude stroom = 50% x 100A = 50A. F(Hz) is afgesteld op 10Hz, de periode van
het signaal is 1/10Hz = 100ms.
Iedere 100ms volgen een impuls van 100A en een andere van 50A elkaar op.
Keuze van de frequentie :
- laswerk met handmatig toevoegen van metaal : F(Hz) is gesynchroniseerd met het toevoegen van het materiaal
- In geval van dun plaatwerk zonder toevoeging (< 8/10 mm) : F(Hz) >> 10Hz
- In geval van speciaal metaal waarbij vibraties van het smeltbad nodig zijn voor het ontgassen : F(Hz) >> 100Hz
• SPOT PUNTEN
A
V
MEM
PROG
10s
20s
0s
MADE IN FRANCE
S / Hz
V
%
A
TIG SPOT
De grijze zones worden niet gebruikt in deze modus.
• TIG DC - Geavanceerd menu
Het is mogelijk om de Start en Stop-fases van de las-cyclus in te stellen.
START
STOP
Een druk op knop geeft toegang tot deze geavanceerde instellingen. Houd knop
MEM
PROG
langer dan drie seconden ingedrukt, tot de melding SET verschijnt. Vervolgens verschijnt
de melding UP, die continu te zien zal zijn. Wanneer u de knop loslaat, kunt u met de
centrale draaiknop via het keuzemenu naar «SET». Bevestig uw keuze door een druk op
knop
MEM
PROG
.
Door aan de knop te draaien krijgt u toegang tot de volgende geavanceerde instellingen :
Instelling Beschrijving Instellen
I_Start stroom tijdens de fase waarin het lassen gestart wordt 10% - 200%
T_Start duur van de fase waarin het lassen gestart wordt 0s - 10s
I_Stop stroom tijdens de fase waarin het lassen gestopt wordt 10% - 100%
T_Stop duur van de fase waarin gestopt wordt met lassen 0s - 10s
De keuze van de te wijzigen instelling gebeurt met een druk op knop
MEM
PROG
. Wanneer de wijziging met behulp van de centrale knop (l) gedaan is, kunt
u uw keuze bevestigen met een druk op knop
MEM
PROG
.U kunt het geavanceerde menu verlaten door op «ESC» te drukken.
INSTELLING START
TIG HF: start met hoge frequentie zonder contact.
TIG LIFT: start met contact (voor de omgevingen die gevoelig zijn voor HF storingen)
Touch Switch Lift
Pré Gaz 0.5s
<1s
1- Raak het te lassen voorwerp aan met de elektrode
2- Druk op de trekker
3- Trek de elektrode terug.
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys TIG 300 DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys TIG 300 DC in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info