665713

Gys TIG 208 AC-DC HF Manual

14
Zoom out
Zoom in
Previous page
1/64
Next page
14/64
Memories saving and recall
There are 5 memories to save and recall TIG parameters. As well as these memories, the machine also
stores the last activated settings and recalls them when the machine is re-started.
Input
3- Press the button
4- "In" is displayed after 1 second.
As long as the display indicates "In", the action can be cancelled.
5- After one second, the display indicates a program number (P1 to P5),
keeping the button pressed, turn the wheel to select the memory
number. Release the button to store the parameters.
Recall a set-up
Proceed as above but after pressing the button
Reset factory parameters
1- Press the reset button for 3 seconds.
2- The display indicates "Ini".
All stored memory has been deleted (the factory parameters have been
restored for the 5 programs + start parameters).
Recommended combinations
Current (A
Ø Electrode (mm)
= Ø wire (filler metal)
Ø Nozzle (mm)
Flow rate
(Argon L/mn)
DC
0,5-5
10-130
1,6
9,8
6-7
4-6
130-160
2,4
11
7-8
Current (A
Ø Electrode (mm)
= Ø wire (filler metal)
Ø Nozzle (mm)
Flow rate
(Argon L/mn)
AC
1-2,4
50-90
1,6
9,8
6-7
2,4-3,2
80-150
2,4
9,8
7-8
3,2-5,0
120-200
2-2,4
9,8-15,7
8-10
Electrode grinding
On TIG AC mode
The electrode will not need grinding, except when using a very low current <50A. It is normal for a ball to
appear at the end of the electrode. The ball size will become larger as the current and balance is increased.
On TIG DC mode
To optimise the welding process, it is recommended to grind the electrode prior to welding as described in
the diagram below :
d
l
Trigger command connector
The trigger command socket is laid out in the following way:
L = 3 x d for a low current
L = d for a strong current
L
Switch GND + Potentiometer
Cold current button
Welding torch button
Cursor / potentiometer
+5V potentiometer
10 KΩ
3
1
4
5
2
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys TIG 208 AC-DC HF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys TIG 208 AC-DC HF in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info