665727
8
Zoom out
Zoom in
Previous page
1/33
Next page
8
6. Set the gas flow on the gas bottle regulator and then open the valve of the torch
7. To strike an arc :
a- Touch workpiece with the
electrode.
b-
Raise the electrode from
2 to 5 mm
from the
workpiece.
8. At end of the weld :
Up 2 times the arc (up-down-up-down) to start the automatic downslope (see paragraph below). This
movement must be performed in less than 4 sec, at a height of 5 to 10 mm. Then close the valve to
stop the gas after cooling the electrode.
Automatic downslope with adjustable time
Function activation :
This function enables to have a clean weld and to avoid cracks and craters at the end of the weld by
gradually decreasing the welding current until the arc stops. By default this function is not activated. To
active it proceed as follow:
1- Press the selector key
2. Adjust the downslope time from 1 to 10 sec (display) using key .
3. Save the required value by pressing the selector key .
Recommended combinations / Electrode grinding
Current (A)
Ø Electrode (mm)
= Ø Rod (filler metal)
Ø Nozzle
(mm)
Flow rate
(Argon L/mn)
0.5-5 10-130 1.6 9.8 6-7
4-8
130-200
2.4
11
7-8
To optimize the quality of the weld, use an electrode grinded as below :
d
l
THERMAL PROTECTION & DUTY CYCLE
Thermal protection: thermal protection light turns on and the cooling time is about 1 to 5 min according
to external temperature.
Leave the machine connected to the power supply after welding in order to let it cool down.
The device described has an output characteristic of 'constant current' type. The duty cycle is indicated in
the table below according to EN60974-1 Norm.
PROGYS 200 A PFC
X% @
I max
X% @
I max
20%
200A
27%
200A
60%
120A
60%
145A
100%
90A
100%
117A
MAINTENANCE
Refer all servicing to qualified person.
Disconnect the unit from the mains and wait until the fan stopped before working on the unit. Inside the
device, voltage and current are dangerous.
L = 2.5 x d.
L
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys PROGYS 200A PFC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys PROGYS 200A PFC in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info