665726

Gys PROGYS 180A Manual

12
Zoom out
Zoom in
Previous page
1/48
Next page
12
PROGYS 180A
MADE IN FRANCE
EN
MAINTENANCE / RECOMMENDATIONS
• Maintenance should only be carried out by a qualied person. Annual maintenance is recommended.
• Ensure the machine is unplugged from the mains, and wait for two minutes before carrying out main-
tenance work. DANGER High Voltage and Currents inside the machine.
• Remove the casing 2 or 3 times a year to remove any excess dust. Take this opportunity to have the
electrical connections checked by a qualied person, with an insulated tool.
• Regularly check the condition of the power supply cable. If the power cable is damaged, it must be
replaced by the manufacturer, its after sales service or an equally qualied person.
• Ensure the ventilation holes of the device are not blocked to allow adequate air circulation.
• Do not use this equipment to thaw pipes, to charge batteries, or to start any engine.
INSTALLATION – PRODUCT OPERATION
HARDWARE DESCRIPTION
The PROGYS 180A is a single phase Inverter “stick welder” for MMA electrode welding with direct current (DC). It is
capable of welding all type of electrodes: rutile, cast-iron, basic, stainless steel. It is over-voltage protected when used
on power generators (230 V +- 15%)
POWER SUPPLY – STARTING UP
• This device is delivered with a 16A plug type EEC7/7. It must be connected on a 230 V (50-60Hz) socket WITH earth.
The absorbed effective current (I1eff) is 16A, for maximal using conditions. Check the power supply and its protection
(fuse and/or circuit-breaker) are compatible with the required current during use. In some countries, changing the plug
can be necessary to allow a use at maximal conditions. Use a 32A plug for intensive use. The device must be placed so
that the power supply is accessible.
• To start the device, turn the potentiometer to the desired current position. Put the potentiometer on «O» for standby
mode.
• Connect the earth clamp and electrode-holder in the quick-plugs. Respect the polarity indicated on the electrode pac-
kaging.
CONNECTION ON A GENERATOR
The machine can work with generators as long as the auxiliary power matches these requirements :
- The voltage must be AC, always set as specied, and the peak voltage below 400V,
- The frequency must be between 50 and 60 Hz.
It is imperative to check these requirements as several generators generate high voltage peaks that can damage these
machines.
CONNECTION ON A GENERATOR
The machine can work with generators as long as the auxiliary power matches these requirements :
- The voltage must be AC, always set as specied, and the peak voltage below 400V,
- The frequency must be between 50 and 60 Hz.
It is imperative to check these requirements as several generators generate high voltage peaks that can damage these
machines.
PRODUCT FEATURES
• Apply the usual welding rules.
• Leave the machine connected to the power supply after welding in order to let it cool down.
• Thermal protection : in case of over-heating the thermal protection light turns on. The cooling time is about 2 to 5 min
according to external temperature.
Mode MMA
• Your machine is equipped with 3 specic functions to Inverters :
- The Hot Start increases the current at the beginning of the welding.
- The Arc Force increases the current in order to avoid the sticking when electrode enters in melted metal.
- The Anti Sticking allows you to easily withdraw your electrode without damaging it in case of sticking.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys PROGYS 180A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys PROGYS 180A in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info