665823
22
Zoom out
Zoom in
Previous page
1/50
Next page
22
NEOPULSE 270-T1 / 270-T2 / 300
EN
There are 3 ways to adjust the welding parameters:
- wire speed:
- metal thickness:
- welding current :
: shows the theoretical welding current
: allows adjustment of the arc length
: The smoothing coil enables the arc strength to be adjusted by
modifying the pulse on standard welding or the pulse frequency on
pulsed welding.
At the end of the weld, a peak of current is used cut the wire and to ensure a clean re-arc. This peak of cur-
rent can be a problem on thin metal, in this case the « burn-back » option can be selected to nish the wire
with a more traditional 'ball' and will limit the energy supplied at the end of the weld in order to preserve
the welding bead.
PLS & PIP mode
The icon allows you to enter the welding process menu and modify the settings of each stage (pre-gas, hot-
start, Upslope, downslope, burn-back, post-gas). This menu is only available with the PRO interface. (see « setup
menu», last page).
Pulse (PLS)
GAS PRE-FLOW : pre-gas time before welding.
CREEP_SPEED : reducing coefcient of the approach speed
(Reduce for thick sheets, e.g.
50% . Do not change for thin metal sheets, e.g. : 100%).
Overcurrent, useful with aluminium (eases the arc strike) to preheat the metal piece (>
100%) or useful with steel during the approach phase (< 100%), can also improve the arc’s
ignition.
T Hot start : preheating phase time in 2T mode. For the 4T mode, enter another value
than 0 to activate it.
Delta U Hotstart : acts on the arc length during preheating phase.
Upslope time.
Delta U Upslope : acts on the arc length during upslope phase.
Downslope : downslope time.
Delta U Downslope : acts on the arc length during downslope.
I Crater Filler : only active in 4T, can set the current level to prevent pinholes at the end
of the weld.
Delta U Crater ller : acts on the arc length during pinhole lling phase.
Post gas ow duration.
Pulse in Pulse (PIP) or double
pulse
Same settings in Pulse mode (PLS). See previous paragraph for more details. There are extra
phases specic to the PIP (Pulse In Pulse) mode :
I cold : current proportion for the background current phase.
Delta U Cold : acts on the arc length during the cold phase.
THigh : current proportion for the welding current (main/hot phase).
TPulse : phase duration.
Can also adjust the pulse frequency on the welding curve (using the control panel).
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys NEOPULSE 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys NEOPULSE 300 in the language / languages: English, German, French as an attachment in your email.

The manual is 5,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info