665823
19
Zoom out
Zoom in
Previous page
1/50
Next page
19
NEOPULSE 270-T1 / 270-T2 / 300
EN
PERFORMANCE
NEOPULSE 270-T1 / 270-T2 NEOPULSE 300
400V - 3~
230V - 3~
(Neopulse T2 only)
400V - 3~ 230V - 3~
X / 60974-1 @ 40°C
(T cycle = 10 min)
20% 60% 100% 40% 60% 100% 40% 60% 100% 45% 60% 100%
I
2
280A 190A 170A 220A 190A 170A 270A 240A 200A 240A 220A 200A
U
2
28.6V 23.5V 22.5V 25V 23.5V 22.5V 27.5V 26V 24V 26V 25V 24V
DESCRIPTION
The NEOPULSE is a semi-automatic welding unit; ventilated for semi-automatic welding (MIG or MAG) and can weld
steel, stainless steel and aluminum. Adjustment is quick and easy with its « synergic wire speed » function.
ELECTRICITY SUPPLY
The absorbed effective current (I1eff) shown on the machine is when used at maximum output. Check that the power
supply and its protection (fuse and/or circuit-breaker) are compatible with the necessary current during use.
The device must be placed in such way that the power socket is always accessible.
Do not use an extension cord which has a wire section smaller than 1.5 mm².
The NEOPULSE is supplied with a 16A plug 5 poles (3P+N+PE) 400V CEE17.. It must be connected to a 400 V (3PH)
supply WITH earth and protected by a circuit breaker (16A and 1 differential 30mA).
It can also be used on a 230V network (3Phase + PE), 50/60 Hz, then it will be advised to use the correct 20A plug.
- The machine will warn you if it is connected to a power supply under 360Veff or over 440Veff.
- Protected against overvoltage, the NEOPULSE will switch off automatically.
DEVICES PRESENTATION (FIG 1)
1 Display + incrementing button 8 Toggle switch Wire feed / Gas purge
2 Reel support 9 SD card support
3 Standard or Push Pull torch connection 10 ON / OFF switch
4 Connection for the earth 11 Power supply cable
5 Push Pull torch command connector 12 Cooling unit connector
6 SpoolGun torch command connector 13 Standard or Push Pull torch gas connection
7 SpoolGun torch power connector 14 SpoolGun torch gas connector
SEMI-AUTOMATIC WELDING FOR STEEL / STAINLESS STEEL (MAG MODE)
This device can weld 0.6/0.8/1 mm steel wires and 0.8/1 mm stainless steel wires.
The machine is delivered with Ø 0.8/1 rollers for steel and stainless steel welding. The value visible on the roller when
in place, is the wire diameter currently in use (FIG-3-B).
For Steel or Stainless Steel, you will need to use specic gas - Argon + CO2 (Ar + CO2). The proportion of CO2 will vary
depending on usage. For the specic requirements, seek advice from your gas distributor.
The gas ow for steel is between 8 and 15L / min depending on the environment.
SEMI-AUTOMATIC WELDING FOR ALUMINIUM (MIG MODE)
This device can weld 0.8/1/1.2 mm aluminium wires.
To weld aluminium, neutral gas “pure Argon” (AR) is required. When choosing gas, ask a gas distributor for advice. The
gas ow in aluminium should be between 15 and 25 L / min depending on the environment.
Things to note when welding with Aluminium
- Rollers: Use rollers specic to aluminium welding (U groove)
- Roller pressure: Set the pressure of the rollers to minimum so as not to crush the wire
- Capillary tube: Do not use a capillary tube when welding aluminium
- Torch: When welding aluminium use a special aluminium torch with Teon sheath to reduce friction. Do not cut the
sheath near the connector! It is used to guide the wire from the rollers.
- Contact Tip: Use the specic Aluminium contact tip corresponding to the diameter of the wire.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys NEOPULSE 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys NEOPULSE 300 in the language / languages: English, German, French as an attachment in your email.

The manual is 5,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info