665823

Gys NEOPULSE 300 Manual

18
Zoom out
Zoom in
Previous page
1/50
Next page
18
NEOPULSE 270-T1 / 270-T2 / 300
EN
This equipment must be used and stored in a place protected from dust, acid, gas or any other corrosive substance.
Attention: this equipment does not comply with the standard IEC61000-3-12. If the machine is connected to the public
network on low voltage, the installer and operator must ensure that the machine can be connected - consult your power
supplier if necessary.
In order to reduce possible electromagnetic disturbances, you can:
Install electric lters close to the socket in case of excessive conducted disturbances. The earth and torch cables should
be as short as possible and be placed close together as far as possible from any other cable, power tool or electrical
cables.
The electromagnetic elds can disturb other equipment, eg; pacemaker or hearing aid.
People wearing pacemakers are advised to consult their doctor before using this device.
Do not use the welding unit to thaw pipes.
Handle gas cylinders with care. There is increased danger if the bottle or it’s valve are damaged.
Electric and magnetic elds may interfere with netwok cables and may cause disturbances.
Never wrap the welding leads around your body. Do not place your body between the earth and the torch cable, they
should be placed on the same side.
Electromagnetic disturbances should be reduced as much as possible if they disturb the operator's activity. The operator
is responsible for the installation and the use of the welding equipment and should seek advice from the manufacturer
if required.
ELECTRIC WIRING RULE TO REDUCE DISTURBANCES
It is sometimes useful to set all the parts at the same voltage (while respecting the standards in place for each).
Installing an earth connection to the workpiece may reduce the disturbances, and will not increase the risk to the ope-
rator or any other electrical appliances.
The shielding of the welding cables and of any other cables may be useful.
IP PROTECTION
IP23S
- Protective case prevents access to hazardous parts with ngers or other solid foreign bodies with a diameter equal to
or higher than 12.5mm
- Protective grid - against rain fall at an angle of 60°.
- Case protects against effects of water/dust penetration when the equipment is not in use.
SET UP
Only qualied personnel authorized by the manufacturer should perform the installation of the welding equipment.
During set up, the operator must ensure that the machine is unplugged. The serial or parallel connections on a generator
are prohibited.
TRANSPORTATION OF THE MACHINE
Two handles are tted on the equipment to carry it easily, be careful to not underestimate its weight.
This machine is not equipped with a lifting fascility - the operator is required to make the necessary arrangements for
safe lifting and transport of the machine (be careful not to tilt the machine).
Do not use the cables or torch to move the machine. The welding equipment must be moved in an upright position.
Never lift the machine while there is a gas cylinder on the support shelf - follow the separate movement guidelines
specied for the gas bottle.
The removal of the wire reel from the machine is recommended before undertaking any lifting operation.
SETTING UP THE MACHINE
Rules to follow:
- Put the machine on the oor (maximum incline of 15°.)
- Ensure the work area has sufcient ventillation for welding, and that there is easy access to the control panel.
- The machine must be placed in a sheltered area away from rain or direct sunlight.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys NEOPULSE 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys NEOPULSE 300 in the language / languages: English, German, French as an attachment in your email.

The manual is 5,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info