665817

Gys MAGYS 400-4 Manual

13
Zoom out
Zoom in
Previous page
1/62
Next page
13
MAGYS 400-4 / 400 GR / 500 GR / 500 WS
EN
CONTROL PANEL (FIG-4):
Welding mode selection / test (1) :
- 2T: two-stage welding / 4T: four-stage welding.
- SPOT: Spot welding with adjustable spot diame-
ter
- Delay: intermittent welding modes for an opti-
mised operating procedure
2 modes to make easier the setting up of the welding
unit: « Manual » or « Synergic ».
- Test function: The LED switches on when you
push the button (1). Read chapter «Welding unit set-
tings»
Voltage display (9) :
By pulling the trigger (The LED indicates that your
torch is on) the voltage will be displayed according to the
parameters selected.
Power adjustment switch (12): 20 positions for the
Magys 400-4, 400 GR and 30 for the 500 GR / 500 WS.
SPOT / DELAY potentiometer (3): To adjust the wel-
ding time of a point, the size of the point and the time
between each point.
Wire speed setting (2): Potentiometer to adjust the
wire speed. The speed can vary from 1 to 24 m/minute.
Note for the MAGYS 400 GR/500 GR/500 WS: It is pos-
sible to select either the potentiometer of the separate
wire feeder or the generator.
See chapter «wire speed potentiometer» and the sticker
inside the wire feeder
Arc dynamics potentiometer (4): To adjust automati-
cally or manually the arc dynamics.
Metal selection and manual mode (5): Read chapter
«Welding unit settings»
Mode « Synergic » (6): Read chapter «Welding unit
settings»
Welding current display (10): indicates the ampe-
rage (LED « A ») or the thickness (11) recommended
according to the power selected (read « test » function
in the chapter « Welding unit settings »).
Note: « NOP » on the display indicates that the welding
current selected is superior to the one recommended
taking into account the parameters (type and diameter
of the wire).
Wire diameter (7): Select the wire diameter used.
Thermal protection LED (8): Read chapter «Thermal
protection».
WELDING UNIT SETINGS: (FIG-4)
« SYNERGIC » MODE
This function automatically controls the wire speed. There is no need to set the wire speed manually.
- Position the potentiometer (2) in the middle of the « Optimal synergic » zone
- Select: Wire type (5), wire diameter (7), power mode (with the 2 power switches on the front (12)).
From the settings chosen, the unit determines the optimum wire speed and is ready to weld. It is also possible to ma-
nually adjust the wire speed (+ or –) if necessary using the potentiometer (2). The last welding conguration is saved
in the memory automatically (wire diameter, wire type, mode).
« Test » function
Only in the synergic mode, I twill indicate you the thickness you can weld with the parameters
selected without using any gas or wire. These values are calculated on the basis of a welding
on the at surface. Attention: you have current in the torch, so avoid any contact with any
metallic part.
NOTE: If the gas, the wire diameter, and the metal used are different from the ones selected in the synergic mode, you
will need to switch to the manual mode to set up the welding unit.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys MAGYS 400-4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys MAGYS 400-4 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info