Manual Gys GYSMI 200P (page 11 of 40) (English, German, Dutch, French, Italian, Spanish)

665723

Zoom out

Zoom in

1/40

GYSMI 80P 130P 160P 200P

MADE IN FRANCE

POWER SUPPLY – STARTING UP

• This hardware is supplied wih a 16A plug, type CEE7/7 (Standard 13A UK plug in the United Kingdom). The machine

must be connected to a socket WITH earth 230V (50 – 60 Hz). The absorbed effective current (I1eff) is displayed on the

machine, for optimal use. Check that the power supply and its protection (fuse and/or circuit breaker) are compatible

with the current needed by the machine. In some countries, it may be necessary to change the plug to allow the use

at maximum settings. Prefer a 20A socket for the 130P, 25 A for the 160P and 32A for the 200P in intensive use. The

device must be positioned so that the socket is always accessible.

• Starting the 80P, 130P, 160P et 200P is done by positionning the switch on the desired current value (the sleep mode

corresponds to the «

» value of the potentiometer).

CONNECTION ON A GENERATOR

The machine can work with generators as long as the auxiliary power matches these requirements :

- The voltage must be AC, always set as specied, and the peak voltage below 400V,

- The frequency must be between 50 and 60 Hz.

It is imperative to check these requirements as several generators generate high voltage peaks that can damage these

machines.

MMA WELDING (ELECTRODE)

CONNECTIONS AND RECOMMENDATIONS

• Connect the cables, electrode holder and earth clamp in the connectors,

• Respect the welding polarity and required current indicated on the electrodes boxes,

• Remove the electrode from the electrode holder when the machine is not in use.

• Your machine has 3 features exclusive to Inverters :

- Hot Start delivers initial overcurrent to facilitate easy arc striking.

- Arc Force adjusts the arc voltage to compensate for the arc length increasing/decreasing

- Anti-Sticking technology prevents your electrode sticking to the work piece

• The welding machine has a constant voltage output in MMA. Duty cycles

• The duty cycle following the norm EN60974-1 is indicated in the table here below:

X @ 40°C (T cycle = 10 min) 80P 130P 160P 200P

I max 6% @ 80 A 5% @ 130 A 14% @ 160 A 16% @ 200 A

60% 31 A 45 A 85 A 120 A

100% 29 A 40 A 70 A 85 A

While under intensive use exceeding the duty cycle (> to duty cycle) the thermal protection can turn on, in this case, the

machine swictes off and the thermal protection indicator light switches on until the machine returns to normal operting

temperature. The tests have been realized at 40 °C.

TIG WELDING WITH INERT GAS (TIG MODE DC)

These machines can weld DC TIG with scratch start (80P/130P/160P/200P) and with LIFT ignition (E160/E200FV.

Requires optional valve controlled TIG torch

TROUBLESHOOTING

Symptoms Causes Remedies

The 2 indicators are on, the machine

does not deliver any current.

The thermal protection has switched

on.

Wait for the end of the cooling cycle.

The green indicator is on, but the

machine does not weld.

Fault with earth clamp/cable connec-

tion.

Check the connections

The product is under voltage, you are

feeling tingling when touching the

machine's body.

The earth contact is faulty. Check the plug and the earth of your

installation.

The machine welds poorly. Polarity error (+/-). Check the polarity (+/-) recom-

mended on the electrode box.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gys GYSMI 200P in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gys GYSMI 200P Manual

Product: