625738
14
Zoom out
Zoom in
Previous page
1/57
Next page
14
GYSFLASH 30-24 HF
EN
BATTERY CHANGE MODE CONFIGURATION
CHANGE BATTERY
12V
CHANGE BATTERY
12V
6V
12V
24V
Start up :
• Connect
1 : Red clamp to the (+) of the battery / battery terminal,
in such a way that the battery can be changed without
disconnecting the clamp.
2 : Black clamp to the vehicle chassis or earth.
• Push the START/STOP key to start the mode.
• During use the current consumed and the instanta-
neous voltage are displayed.
• When changing the battery ensure the polarity is
correct. While exchanging the batteries, be careful
not to disconnect the charger clamps to avoid loss of
electronic data.
STARTING BATTERY CHANGE
CHANGE BATTERY
CHANGE BATTERY
U=12.9V I=26AU=12V
Warning: polarity reversal can damage the vehicle electronics.
POWER SUPPLY MODE (OPTIONAL)
This mode is intended for expert users only. This mode enables the charger to be used as a stabilised power supply, with regulated
voltage and adjustable maximum current. By default this mode is inactive and doesn’t appear in the mode list. It can be activated
via the Advanced menu (see page 16).
Adjustment of the voltage regulation and current limitation :
The voltage regulation can be adjusted from 2V to 30V and the maximum current from 2A to 30A (or from 2A to 15A above 16V):
POWER SUPPLY MODE CONFIGURATION
POWER SUPPLY
U=19.6V I<15A
POWER SUPPLY
U=19.6V I<10A
2.0V
2.1V
...
30.0V
2A
3A
...
30A
POWER SUPPLY
U=13.5V I<30A
2A
3A
...
15A
Start up:
• Push the START/STOP key to start the mode.
• During use the current consumed and the instanta-
neous voltage are displayed.
STARTING POWER SUPPLY
POWER SUPPLY
U=19.6V I<15A
POWER SUPPLY
U=19.6V I=10A
NOTE: Unlike the other modes, when in Power Supply mode, the charger does not compensate cables voltage drop.
In this mode, the voltage displayed is the charger output voltage (and not the voltage on the clamps).
CONFIGURATION MENU
Access to conguration menu :
MODE
3 sec - Mode
To browse in the sub menu press the
«Select» key :
SELECT
languages > restart > lock showroom > charge type > cable check >
ADVANCED MENU > Reset Memory
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys GYSFLASH 30-24HF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys GYSFLASH 30-24HF in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info