665742

Gys EASYMIG 150 Manual

18
Zoom out
Zoom in
Previous page
1/86
Next page
EASYMIG 130 / 140 / 150
EN
18
SEMI-AUTOMATIC WELDING FOR ALUMINIUM (MIG MODE)
Set the voltage output and the wire speed according to the thickness of the weld piece, following the instructions/
recommendations printed on the side of the machine.
The Easymig 140 and 150 can be equipped to weld with aluminium wire Ø 0,8 or 1,0 (g II-B / p.74).
The Easy Mig 130 is delivered equipped for welding Aluminium of Ø 0.8mm (Occasional and non-intensive).
In this case the wire used should be stiff to facilitate wire feeding.
For use with aluminium, the gas requirement is pure argon (Ar). For the specic gas requirements please contact
your distributor. The gas ow in Aluminium is between 20 and 30 Litres/minute depending on the environment,
and the experience of the welder.
Below are the differences between welding with Steel and Aluminium :
- Specic rollers are needed for welding with Aluminium.
- Adjust the pressure of the drive rolls to prevent the wire being crushed.
- Only use a capilliary tube for welding with Steel or Stainless Steel.
- Use a special Aluminium Torch with a teon sheath to reduce friction.
DO NOT cut the sheath close to the joint, it is used to guide the wire from the the rollers.
- Contact Tube : Use a special aluminium contact tube specic to the diameter of wire being used.
GASLESS WIRE WELDING
Set the voltage output and the wire speed according to the thickness of the weld piece, following the instructions/
recommendations printed on the side of the machine.
The Easymig can weld gasless wire up to 0.9mm, if the polarity is reversed (g III / p.75) respecting a maximum
pressure of 5Nm. For parameters of use, please refer to the instructions indicated on page 74. Welding gasless
wire with a standard nozzle can lead to overheating and deterioration of the torch. It is recommended to use a
“No Gas” nozzle (ref. 041868), or remove the genuine nozzle (Fig. III / p.75).
ELECTRODE WELDING
• The reverse polarity cable must be disconnected in MMA (stick welding) mode in order to connect the electrode
holder and earth clamp. Connect the electrode holder and earth clamp as indicated on the electrode packaging.
• Respect the basic rules of welding.
• This device has 1 feature specic to Inverter machines :
- Anti-Sticking: Enables easy removal of the electrode from the metal. The anti-sticking feature, after its start,
requires approximately a 3 seconds delay before resuming normal welding operations.
SETTINGS PANEL (FIG V / P.75)
1
• Green light «ON»: when the machine is switched on the light
turns on.
• In case of power failure, the green light goes off but the device
remains powered while the power cable is unplugged.
2
• Orange light :
• Over-temperature: in such a case you shall wait a few minutes,
the light will turn off and the machine will start again.
• Over-current on primary circuit: in such a case you shall switch
off the machine (with the main switch) and switch on.
3
• Left button:
- MIG / MAG Welding : Adjust the wire feeder speed up to
maximum speed.
- MMA welding : Adjust the welding current.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys EASYMIG 150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys EASYMIG 150 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info