665741

Gys EASYMIG 140 Manual

19
Zoom out
Zoom in
Previous page
1/86
Next page
EASYMIG 130 / 140 / 150
EN
19
4
• Right button:
- Adjust the voltage reference up to the maximum value.
Advices
The wire speed adjustment is often determined « by the noise »: the arc must be stable and have a low
crackling.
If the speed is too low, the arc is not continuous.
If the speed is too high, the arc crackles and the wire pushes back the torch.
PROCESS OF REELS AND TORCHES ASSEMBLY (FIG IV / p.75):
• Remove the contact tube and its support (g D), and the nozzle (g E) from the torch.
Fig A : • Position the wire reel on the reel support :
• Adjust the reel brake (1) to avoid reel movement tangling the wire when welding stops. Be careful not to tighten
too much.
Easymig 150 : For a 200mm wire reel tighten the reel to the maximum. The adaptor (4) is only to be used for a
200mm reel.
Fig B : The drive rollers included have 2 grooves (0,8 and 0,9). For 0.8mm steel wire, use the V shaped groove.
For ux cored wire, remove and reverse the roller to use the 0.9mm groove.
For 0.8mm aluminium wire, remove and replace the roll with a model specically designed for aluminium with a
U shaped groove (not included).
Fig C : To select the adjustment of the drive rollers.
• Loosen the drive roller knob (3) as far as possible and insert the wire, tighten the knob again slightly.
• Start the motor by pressing the trigger of the torch.
• Tighten the knob whilst pressing the trigger until the wire starts to move.
Nb : When welding with Aluminium, use the minimum possible pressure to avoid crushing the wire
• Leave about 5cm of wire out of the torch, then put the contact tube (g. D), and the nozzle (g. E) adapted to
the wire to be used at the extremity.
GAS COUPLING
- Connect a pressure regulator to the gas bottle. Connect the welding machine using the pipes supplied, and
place the two clamps to avoid leakages.
- Set the gas ow by adjusting the dial located on the pressure regulator.
NB : to help facilitate the adjustment of the gas ow, operate the drive rollers by pressing the trigger of the torch
(ensure that the drive roller is completely loose so the wire is not fed through).
This procedure does not apply to «Gasless» welding mode.
DUTY CYCLE & WELDING ENVIRONMENT IN USE
• The machine has a “constant output” (constant voltage) in MIG/MAG mode; and a “dropping output” (constant
current) in MMA mode. The duty cycles following the standard EN60974-1 (at 40°C on a 10mn cycle) are indi-
cated in the table here below:
X @ 40°C
(T cycle = 10 min)
I max
60% (T cycle = 10
min)
100% (T cycle =
10 min)
EasyMIG 130 – MIG/MAG 20% @ 120A 70A 60A
EasyMIG 130 - MMA 20% @ 100A 60A 50A
EasyMIG 140/150 – MIG/MAG 15% @ 140A 80A 70A
EasyMIG 140/150 - MMA 15% @ 120A 70A 60A
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys EASYMIG 140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys EASYMIG 140 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info