665741

Gys EASYMIG 140 Manual

17
Zoom out
Zoom in
Previous page
1/86
Next page
EASYMIG 130 / 140 / 150
EN
17
MAINTENANCE / RECOMMENDATIONS
• Maintenance should only be carried out by a qualied person. Annual maintenance is
recommended.
• Ensure the machine is unplugged from the mains, and wait for two minutes before carrying
out maintenance work. DANGER High Voltage and Currents inside the machine.
• Remove the casing 2 or 3 times a year to remove any excess dust. Take this opportunity
to have the electrical connections checked by a qualied person, with an insulated tool.
• Regularly check the condition of the power supply cable. If the power cable is damaged, it
must be replaced by the manufacturer, its after sales service or an equally qualied person.
• Ensure the ventilation holes of the device are not blocked to allow adequate air circulation.
• Do not use this equipment to thaw pipes, to charge batteries, or to start any engine.
INSTALLATION – PRODUCT OPERATION
DESCRIPTION
Thank you for chosing this machine. To get the best use from your machine, please read the following carefully :
The Easymig range are semi-automatic MIG/MAG, MMA and ux cored wire welding stations. They are manual
settings machine, with the help of the table printed on the product. They are recommended for welding steel,
stainless steel and aluminium.
ELECTRICITY SUPPLY
The absorbed current (I1eff) is indicated on the device at maximum usage. Check that the power supply and
its protection (fuse and/or circuit breaker) are compatible with the current needed for use. In some countries, it
might be necessary to change the plug to allow maximum performance. The device must be installed so that the
mains socket is accessible.
Do not use an extension cable with a diameter of less than 1.5mm². Easymig is delivered with a 16amp plug
(TYPE CEE7-7).
This machine must be connected to an EARTHED power supply 230V, 50/60 Hz, and protected by a 16A circuit
breaker .
MACHINE DESCRIPTION (FIG I / p.74)
1 : Adjustment of welding settings (wire speed and
welding voltage).
2 : Switch MIG/ MMA
3 : European standard torch connection.
4 : Connectors
5 : Polarity reversal cable
6 : Power Cable (2.20 m)
7 : Power switch
8 : Reel adaptor 100 mm (Easymig 130/140)
or 100/200mm (Easymig 150)
SEMI-AUTOMATIC WELDING FOR STEEL / STAINLESS STEEL (MAG MODE)
Set the voltage output and the wire speed according to the thickness of the weld piece, following the instructions/
recommendations printed on the side of the machine.
The Easymig can weld Steel wire 0.6/0.8mm, and Stainless Steel of 0.8mm.
The machine is tted with Ø 0.8mm Steel or Stainless Steel rollers. The contact tube, the groove of the roller
and the sleeve of the torch are all compatible with 0.8mm wire. Should you wish to weld 0,6 wire, use a torch of
maximum 3m long. The contact tip must be changed (g II A / p.74) as well as the wire feeder’s roller that must
be replaced by an optional reference (042339) with a 0.6 diameter groove. In this case, the position in such
a way to observe 0.6. For use with Steel, the gas requirement is argon + CO2. (Ar+CO2). The proportion of
CO2 required will vary depending on the use. For Stainless Steel, use the combination of 2% CO2 For specic
gas requirements, please contact your gas distributor. The gas ow in steel is between 8 and 12 Litres/minute
depending on the environment.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys EASYMIG 140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys EASYMIG 140 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info