625733

Gys BATIUM 25-24 Manual

8
Zoom out
Zoom in
Previous page
1/24
Next page
8
BATIUM 25/24
CHARGING FUNCTION IUIO
This function enables to charge lead traction batteries for forklift truck, fork lift, industrial oor cleaning machine, with batteries from
35 Ah to 180 Ah. To connect the charger, process as below:
1. Directly on the battery, use the standard charger clamps
2. On the specic charger plug, replace the clamps at the cable end by the connector adapted to your machine. Respect the polarity
and the current scale.
Find below the charging process :
Voyant allumé Achage
Phase 1 :
Voltage rise
Charging
current
Phase 2 :
Voltage regulation (during 2 hours)
Charging
current
Phase 3 :
Charge end (Floating)
Nb: If the battery stays connected after the the end of the charge, each 72h, Batium 25/24 starts again a charging cycle
to keep the battery 100% charged.
FORCED CHARGE FUNCTION
In case of a deeply discharged battery, (Voltage under 2V), Batium remains in hold and displays:
. A chain of lights on the current screen
. The indicators « battery voltage », « capacity » and « charging curve » are on.
To force thecharge, press 5 seconds on the key (2) until Batium indicates CHE (=check). The charger detects a battery with a
voltage above 0.8 V.
As for the other models, this step is divided into 2 steps:
1. Diagnostic step (battery voltage analysis).
Nb : For 12v or 24 V batteries, during this step, as your battery is discharged, Batium will detect and offer you a 6V voltage. To
validate or adjust the voltage, press (2) (in less than 10 sec after the rst press). See anomaly 6.
2. Recovery step (voltage rise). This step may last up to 30 minutes max.
The diagnostic stage is over (CHE), Batium carries on with normal charge. For more information on the charging process, please
refer to the subdivision Charging function IUoU.
SOS RECOVERY FUNCTION
This function concerns all automotive batteries which are deeply discharged (IUoU).
After the battery has been plugged in, BATIUM does a diagnosis of the battery: Light signal « CHE » displayed.
If after 1 minute, the signal “SOS Recovery” ashes, this means the battery is sulfated.
The “SOS Recovery” function, thanks to a specic charge curve, starts a 24 hours recovery cycle.
To activate this function, proceed as following:
1. Disconnect the battery from the mains. (HIGH VOLTAGE RISK)
2. Connect the Batium to the outlet, then turn the device ON.
3. Select the IUoU charge curve.
4. Activate « SOS Recovery » by pressing during 5 seconds the «SOS recovery» key till the light (6) lights up.
5. Select the battery voltage and charging speed.
6. Connect the Batium’s clamps on the battery, the desulfation of the battery starts.
Indicators lit Displaying
Step 1:
Analyze, starting of the desulfatation and restoration of the
battery
Display of the current.
According to the battery behavior, the
current may increase or decrease.
Step 2 :
Desulfatation
Display of the current
Step 3 :
End of charge.
Battery irretrievable
Batterie saved
PROTECTIONS
The Batium is protected against short-circuits, polarity inversions and engine starts. It has an anti-spark feature which prevents sparks whilst
the battery is connected to the Batium. The Batium will not deliver current if there is no battery detected (no voltage in the clamps).
EN
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys BATIUM 25-24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys BATIUM 25-24 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info