624895

Gude WS 230-2350 R 58109 Manual

21
Zoom out
Zoom in
Previous page
1/96
Next page
D
17
ENGLISH
GB
Additional Safety and Working Instructions
When grinding metal, ying sparks are produced.
Take care that no persons are endangered. Because
of the danger of re, no combustible materials
should be located in the vicinity (spark ight zone).
Do not use dust extraction.
Avoid ying sparks and sanding dust hit your body.
Never reach into the danger area of the machine
when it is running.
Chips and splinters must not be removed while the
machine is running.
Immediately switch o the machine in case of con
-
siderable vibrations or if other malfunctions occur.
Check the machine in order to nd out the cause.
Do not let any metal parts reach the airing slots -
danger of short circuit!
Under extreme conditions (e.g. smooth-grinding
metals with the arbour and vulcanized bre grinding
wheel), signicant contamination can build up on
the inside of the angle grinder. For safety reasons,
in such conditions the inside should be cleaned
thoroughly of metal deposits and a motor circuit-
breaker must be connected in series. If the motor
circuit-breaker trips the machine must be sent for
repair.
For accessories intended to be tted with threaded
hole wheel, ensure that the thread in the wheel is
long enough to accept the spindle length.
Always use and store the cutting and grinding disks
according to the manufacturer‘s instructions.
Always use the correct guard for cutting and grin
-
ding.
Always use guard with cutting guide from the acces
-
sories range for cutting stone.
The adjusting nut must be tightened before starting
to work with the machine.
Always use the auxiliary handle.
The workpiece must be xed if it is not heavy enough
to be steady. Never move the workpiece towards the
rotating disk by hand.
STARTING CURRENT LIMITER
The starting current for the machine is several times
greater than rated current. The starting current
limiter reduces the starting current to such an extent
that a fuse (16 A, slow-blow) is not tripped.
SMOOTH START
Electronic smooth start for save use prevents jerky
run-up of the machine.
Mains Connection
Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30mA).
Connect only to single-phase AC system voltage as
indicated on the rating plate. It is also possible to
connect to sockets without an earthing contact as
the design conforms to safety class II.
Only plug-in when machine is switched o.
Maintenance
Unplug the machine before any work on it.
Repairs and works specied in these Instructions may
only be performed by qualied authorised sta.
Use only original accessories and original spare parts.
Keep the device, in particular the air vents, clean at all
times. Never spray water on the device body!
Do not clean the plastics with solvents, ammable or
toxic uids. For cleaning, use a damp cloth only.
Caution! If the power cord of the appliance gets
damaged, it must be replaced by the manufacturer or
its customer service or a similarly qualied person to
avoid danger.
Only a regularly maintained and treated appliance
can serve as a satisfactory aid. Insucient mainte
-
nance and care can lead to unforeseen accidents and
injuries.
If necessary, a list of spare parts can be found at www.
guede.com.
DEGB
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude WS 230-2350 R 58109 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude WS 230-2350 R 58109 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Turkish as an attachment in your email.

The manual is 8,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info