Manual Gude WS 230-2350 R 58109 (page 19 of 96) (English, German, Dutch, Danish, French, Italian, Polish, Turkish)

624895

Zoom out

Zoom in

1/96

ENGLISH

Keep bystanders a safe distance away

from work area. Anyone entering the

work area must wear personal protective

equipment.

Class II tool.

CE marking

Any damaged or disposed electric or

electronic devices must be delivered to

appropriate collection centres.

WARNING

Read all safety warnings and all

instructions. Failure to follow the warningsand

instructions may result in electric shock, re and/or

serious injury.

Save all warnings and instructions for future

reference.

Angle Grinder Safety Warnings

Safety Warnings Common for Grinding, Sanding or

Abrasive Cutting-O Operations:

a) This power tool is intended to function as a

grinder, sander, wire brush or cut-o tool. Read

all safety warnings, instructions, illustrations and

specications provided with this power tool. Fai

lure to follow all instructions listed below may result

in electric shock, re and/or serious injury.

b) Operations such as wire brushing and poli

shing are not recommended to be performed

with this power tool. Operations for which the pow-

er tool was not designed may create a hazard and

cause personal injury.

c) Do not use accessories which are not speci

cally designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked on the

power tool. Accessories running faster than their

rated speed can break and y apart.

e) The outside diameter and the thickness of

your accessory must be within the capacity rating

of your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

f) Treaded mounting of accessories must match

the grinder spindle thread. For accessories

mounted by anges, the arbour hole of the

accessory must t the locating diameter of the

ange. Accessories that do not match the mounting

hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

g) Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive wheels

for chips and cracks, backing pad for cracks, tear

or excess wear, wire brush for loose or cracked wi

res. If power tool or accessory is dropped, inspect

for damage or install an undamaged accessory.

After inspecting and installing an accessory,

position yourself and bystanders away from the

plane of the rotating accessory and run the power

tool at maximum noload speed for one minute.

Damaged accessories will normally break apart during

this test time.

h) Wear personal protective equipment. De

pending on application, use face shield, safety

goggles or safety glasses. As appropriate, wear

dust mask, hearing protectors, gloves and shop

apron capable of stopping small abrasive or

workpiece fragments. The eye protection must

be capable of stopping ying debris generated by

various operations. The dust mask or respirator must

be capable of ltrating particles generated by your

operation. Prolonged exposure to high intensity noise

may cause hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area must

wear personal protective equipment. Fragments of

workpiece or of a broken accessory may y away and

cause injury beyond immediate area of operation.

j) Hold the power tool by insulated gripping sur

faces only, when performing anoperation where

the cutting accessory may contact hidden wiring

or its own cord. Cutting accessory contacting a „live“

wire may make exposed metal parts of the power tool

„live“ and could give the operator an electric shock.

k) Position the cord clear of the spinning accesso

ry. If you lose control, the cord may be cut or snagged

and your hand or arm may be pulled into the spinning

wheel.

l) Never lay the power tool down until the acces

sory has come to a complete stop. The spinning

accessory may grab the surface and pull the power

tool out of your control.

m) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning acces

sory could snag your clothing, pulling the accessory

into your body.

n) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

o) Do not operate the power tool near ammable

materials. Sparks could ignite these materials.

p) Do not use accessories that require liquid

coolants. Using water or other liquid coolants may

result in electrocution or shock.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude WS 230-2350 R 58109 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Turkish as an attachment in your email.

The manual is 8,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude WS 230-2350 R 58109 Manual

Product: