Manual Gude Pro GDS 16 PRO 55097 (page 11 of 82) (English, German, Dutch, French, Italian)

629068

Zoom out

Zoom in

1/82

• Follow all safety and warning instructions on the

appliance and keep them readable.

• The safety equipment on the appliance must not be

disassembled or put out of operation.

• Check the feeder cables. Do not use any defective

feeder cables. See Plugging.

• The saw blade must run freely.

• The processed material must be checked for any

undesirable items such as nails, screws, etc.

• Be caution when working: Risk of injury for fingers

and hands by the saw blade.

• Any changeover, adjustment, measurement and

cleaning to be performed when the engine is off only.

Unplug the appliance.

• Any installation, repair and servicing of the wiring

may only be performed by professionals.

• All protective and safety equipment must be

immediately refitted after finishing any repair and

servicing work.

• Switch the engine off after leaving the place of your

work. Unplug the appliance.

• Any changes to the appliance exclude the liability of

the producer for any consequential damage.

• Do not look directly at the laser beam when your eyes

are not protected.

• Never aim with the laser beam at reflection areas,

persons and animals. Even a low-power laser beam

is able to damage eyes.

•

Caution! - if procedures other than those

specified are taken, it may lead to dangerous

exposure to radiation.

• Never open the laser module.

Use as designated

The fretsaw has been designed to cut angular pieces of

wood or similar workpieces.

Logs may only be cut with appropriate holding means.

The appliance may only be used as designated. Any other

use will be considered a use in conflict with the

designation. The user/operator, not the manufacturer, will

be held liable for any consequential damage or injuries of

all types.

Please be sure to know that the appliance has not been

designed for industrial and craft purposes. We are not

liable if the appliance is used for industrial and craft

purposes or similar activities.

Saw blades suitable for this appliance to be used only.

Using cutting wheels of all types prohibited. The use as

designated principles also include following safety

instructions, assembly instructions and operating

instruction included in the Operating Instructions. Persons

operating or servicing this appliance must be notified and

instructed in respect of possible risks. Moreover,

applicable accident prevention regulations must strictly be

followed.

Other general regulations regarding occupational health

and safety must also be followed.

Any changes to the appliance exclude the liability of the

manufacturer for any consequential damage.

Some residual risk factors cannot be fully ruled out even

when the appliance is used as designated. Due to the

appliance design and assembly, there may be the

following risks:

• Harmful wood dust emissions when used in enclosed

places

• Risk of injury as a result of touching in an exposed

cutting area of the tool

• Risk of injury when changing a tool (risk of cutting)

• Finger/hand jamming

• Risk of backlash

• Workpiece fall due to insufficient supporting area

• Contact with the cutting tool

• Parts of branches and parts of workpiece thrown

away

Assembly

The fretsaw must be unplugged before any servicing

and tool change.

Fitting the saw to bench

To fit the saw, a massive-wood bench is better than a

weak compressed board with vibrations and noise

significantly affecting your work.

Fixing materials necessary for assembly are not included

in the supply.

Example of materials:

4 M8 hex screws

4 Ø 8 mm flat gaskets

4 Ø 8 mm washers

8 M8 hex nuts

For assembly purposes, use the existing assembly holes

(pic. A/6+12). Do not tighten the screws too much. Keep

some clearance so that the rubber legs (pic. A/7+11) could

absorb well.

Saw blade cover fitting – pic. C-D

• Now fold the saw blade cover (pic. A/2) using the

socket head screw (pic. C/a) and the nut (pic. C/b) as

shown in picture C.

• Now fold the saw blade cover (pic. A/2) using the

locking screw (pic. D/1) as shown in picture D.

Saw blade change (original saw blades) – pic. G-I

• Release the saw blade cover by loosening the locking

screw (pic. D/1). Now fold the saw blade cover (pic.

A/2) backwards. Pull the saw blade tension lever (pic.

G/22) up so that the saw blade (pic. H/26) is

loosened.

• Loosen the socket head screw (pic. H/c) on the upper

holder of the saw blade (pic. H/25). Open the

inspection cover (pic. I/27). Loosen the socket head

screw (pic. I/d) on the bottom holder of the saw blade

(pic. I/28). Take the saw blade (pic. H/26) out using

the bench insert (pic. A/4).

• Refit a new saw blade in the reverse order.

• Due to universal saw blade holders (pic. H/25 and

I/28), both fretsaw blades and laminated blades can

be used.

Caution: The saw blade must always be fitted in a

way the teeth are pointed at you and down when

standing in front of the saw.

Spare Güde saw blades can be obtained under Art. No.

#55080, #55081, #55082, #55083 and # 55084

Tilting the saw bench (pic. B)

• Loosen the securing screw (pic. A-B/5).

• Tilt the saw bench (pic. A/3) to the left or to the right

so that the indicator (pic. B/19) shows the required

angle on the scale (pic. B/20).

• Now fix the saw bench (pic. A/3) using the securing

screw (pic. A-B/5).

Caution: If precise work is required, a test cut needs

to be performed and a new angle possibly adjusted.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude Pro GDS 16 PRO 55097 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 4,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude Pro GDS 16 PRO 55097 Manual

Product: