628969

Gude Pro 310-10-50 PRO 75505 Manual

18
Zoom out
Zoom in
Previous page
1/67
Next page
Air consumption of pneumatic appliances / directions for use
Not the electric motor power but the produced air volume (actual power) is decisive for the compressor power. Actual power =
suction power minus app. 35-40% of the power (for each compressors, regardless of the manufacturer). Do not choose too small
compressor power in order not to load it up to the upper limit and to have some reserve for the attached appliances. The air jet size
(capacity in litres) may not be decisive. However, capacity, on the other hand, should not be too small to ensure there is air supply
and the compressor could also cover higher needs in the short term.
If provisions of the generally applicable regulations and these Operating Instructions are not adhered to, the manufacturer cannot be
held liable for any damage.
Action Example of use Directions for use
Necessary
operating
pressure
in bar
Necessary actual
power, air volume
delivered by the
compressor
Blowing Work table cleaning by air,
carburettor cleaning, machine parts
cleaning, cleaning machines off
wooden or metal chips
Short-term use 5 to 11 from 100 I
Spray-painting Water-based paints and thin
varnishes
nozzle 0.5 to 1 mm 3 to 4
Spray-painting
Synthetic resin and nitrocellulose
lacquers, thinned
nozzle 1.2 to 1.5 mm 3 to 5
Spray-painting
Hammer paints and other viscous
lacquers
nozzle min. 2 mm 3 to 5
Minor parts, mudguards
of automobiles, etc. from
120 l.
Entire cars, larger areas
from 280 l.
Spray guns, washing
gun
Cleaners spraying in cold
conditions, oil spraying as
anticorrosion protection, vehicle
bottom protection, insecticides
spraying, etc.
Can be set within the
range of a water jet to
water fog
4 to 7 Depending on the time of
use: 250 l to 400 I
Clipping appliances Wood, cardboard, etc. connecting
using clips within a length of app. 25
mm
Operating pressure
depending on the wood
or material hardness
4 to 7 80 l to 280 I
Nailing appliances Connecting by clips of more 25 mm
and nails within a length of 100 mm
ditto 4 to 7 80 l to 400 l
Pneumatic
superfinishing
appliance
In cars or at bodies As per manufacturer
details
5 to 6 Depending on the time of
use: 300 l to 560 I
Tyre inflation Tyres of car wheels The bigger the
compressor power, the
faster the inflation
Pressure in tyre 120 l to 280 l
Tyre inflation Tyres of trucks or bigger ditto Pressure in tyre 280 l to 560 I
Grease gun All appropriate works As per manufacturer
details
4 to 11 from 80 I
Filler press All appropriate works Use an appliance with
adequate operating
pressure
8 to 15 from 60 I
Pneumatic tools Small drills, rod grinders, etc. As per manufacturer
details
5 to 7 from 180 I
Pneumatic tools
Angular grinder
As per manufacturer
details
5 to 7 from 400 I
Pneumatic tools
Plate shears, sheet cutter, etc.
As per manufacturer
details
5 to 7 from 280 I
Light impact wrenches For screws with a thread within 10
mm
Smaller appliance
enough for short-term
use
5 to 7
from 280 I
Heavy impact
wrenches
For screws with a thread of more
than 10 mm
ditto 5 to 8
from 400 I
Light cutters Cutters for bodies, sheet and small
mason chisels
As per manufacturer
details
5 to 8
from 280 I
Break and blast
hammers
Heavy masonry and concrete
works, tapping
ditto
5 to 10
min. from 460 I
Gun abrasive blasting Only corners, small areas, minor
parts and profiles
ditto
8 to 11 from 300 I
Sandblaster abrasive
blasting
Larger areas and time-consuming
works
ditto
8 to 15 As per manufacturer
details
The above-mentioned values are just of orientation nature as they may differ for appliances of various manufacturers. Works with
higher air requirement may also conditionally be performed with compressors with a lower suction power than the requirement given in
the table. If pressure is reduced in the air jet under the necessary operating pressure, however, an appropriate break must be
introduced after the air jet is pressurised again. In order not to load the compressor when being operated by more than can be
tolerated, we recommend taking into account some power reserve when selecting the right appliance.
18
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude Pro 310-10-50 PRO 75505 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude Pro 310-10-50 PRO 75505 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info