629048

Gude Pro 150 PRO 75170 Manual

20
Zoom out
Zoom in
Previous page
1/26
Next page
Operation
Wear protective glasses! Wear
earphones! Wear a respirator!
Before everyday use, please empty the water from
the compressor tank and blow the condensation
from the air hose.
1. Now you can start the compressor. Service
pressure of 6 bar.
2. The eccentric grinding machine is fitted with
a regulator controlling the speed of the
grinding machine. It can be found under the
compressed air connector.
3. Carefully press the control lever down. Start
the eccentric grinding machine. Put it on the
outer edge of the emery paper while holding
the appliance at a slight angle towards the
working surface. Move the grinding
machine slowly forward and backward so
that passes overlapped each other. Let the
grinding machine work. Do not apply too
much pressure on the grinding machine.
That would mean the grinding machine
extension speed would be decreased,
which would reduce the grinding output.
Moreover, it would load the compressor
engine.
4. When you are finished with grinding, loosen
the control lever and only after that, lift the
grinding machine.
NOTICE: To reach proper results with
grinding, you need to start with an emery
paper that is as rough as possible to be able
to remove any elevation and rough surface.
After that it is necessary to take a finer
emery paper to reach the required
surface structure.
Maintenance and treatment
Lubrication
1. Disconnect the eccentric grinding
machine from air supply.
2. Add 4 – 6 drops of pneumatic GÜDE
oil, Order No. 40060 (we recommend
the GÜDE mist lubricator, Order No.
41354) or corresponding oil to the air
intake while the starter is pressed
down.
3. Now connect the vibration grinding
machine again with air supply and
leave it run for app. 30 seconds to
ensure that the surplus oil runs out.
This lubrication process contributes to the
reduction of humidity, dust and dirt that deposit
over time in the compressor and thus reduce
its output. The best protection against this is
the use of an integrated oil tank.
Safety instructions! Oil run out can
lead to serious injuries. After cloth
lubrication, cover the oil run-out top
and let the grinding machine run for
several seconds to ensure the
surplus oil safety ran out. Please
hold the cloth out of mobile parts!
The air hose must be removed and more
pneumatic oil poured in the air intake every
three months or when the grinding machine is
used less often. Reconnect the air hose and let
the eccentric grinding machine run for app. 30
seconds so that the compressor engine was
cleaned. After cleaning, follow all lubrication
instructions.
Failure removal
Problem Possible cause Solving the problem
Insufficient air pressure Check the air pressure on the air
intake. It must be 6 bar.
Air pressure set too low Set the grinding machine
regulator to the highest level.
Grinding machine must be oil-
lubricated
See the Lubrication part
Grinding machine must be
cleaned
See the Maintenance part
Grinding machine is not working
or is running slowly
Air hose untight Tighten all fixing connections of
the hose.
20
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude Pro 150 PRO 75170 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude Pro 150 PRO 75170 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info