624567

Gude P 2500 94131 Manual

16
Zoom out
Zoom in
Previous page
1/82
Next page
Clamping Screw Set Up
Grinding
Before the start of grinding, the chain should be conducted
between both the attachment guides
Now, the tooth to be sharpened first should be taken against
the stop. Watch out for the sharpening angle to correspond
to the guides position. The type of the chain to be sharpened
should be determined using the sharpening block provided
or the table p.9. There, you can find out the cutting
thickness, angles and dimensions.
Set the guides to the chain width using the set screw u(A) so
that it is firmly fixed in the clamping screw by clamping lever
control (B).
Set the feed by set screw (E).
On severely worn chains, the lateral position of the chain
guide should be secured with a set screw (D).
Set the top plate angle by means of the set screw (p.3, p. 5)
and it may be also read on the scale (F). The vice angle
should be set up by set screw (G).
G
B
A
D
E
F
Vrcholový řezný úhel
(Top Plate Angle)
Úhel ostří
(Vice Angle)
With the clamping screw adjusted and the vice angle set up
(Notice: RH and LH teeth to be differentiated) and preset the
top plate angle, lead the grinding disk down to the tooth by soft
pushing the supporting strut. The grind depth may be set by
set screw (K).
With clamping lever loosen (B), the set screw is being screwed
or unscrewed (E) until the grinding disk to sharpen will touch
the tooth. During the procedure, pull the chain to the guide (L)
carefully.
(Notice. Wear gloves when performing the job!)
K
L
Some types of saw-chains require that the clamping screw be tilted by 5° - 10° (cf. Table: space Tilt angle).
Note the notches (Fig.9).
Now, the machine may be switched on and the saw-chain grinding may be started by a careful thrust on the grinding disk.
Adjust the pressure as necessary. Mark the start of grinding e.g. with a piece of chalk and grind all the teeth in one direction,
then turn the clamping screw (mind the angle) and grind the teeth in opposite direction.
With warn chains, the lateral guide position (Fig.10, position M) shall be set for the grinding disk not to touch the guide.
Avoid any strong thrust as the teeth might collide and the chain would wear and tear too fast.
Notice : Never grind any driven parts.
16
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude P 2500 94131 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude P 2500 94131 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info