622226

Gude MIG 175 ZD-20038 Manual

14
Zoom out
Zoom in
Previous page
1/106
Next page
Type of Welding
a) Manual
Pushing the button on the burner, the wire movement for manual welding will start or stop.
b) Tack welding
Holding the button on the burner, the machine will be welding for a set-up time (set-up 4.12 f) and then it will stop
automatically. Re-pushing the button on the burner, the procedure may be repeated as required.
Welding parameters display
Pushing menu S1 button, it is possible to select any required setup during the welding operation. Set values may be
increased/decreased by using the potentiometer.
Wire movement speed Wire start up time Wire extrusion after Tack welding welding Thermal fuse time
-> display range -> display range -> range -> range
min=05 - max.=99 min=10 – max.=99 min=0 – max.=99 min=10 – max.=80
Symbols Glossary
This default may be recalled by push menu S1 button:
c)
Wire Feed Speed : control by turning potentiometer /ENC
d)
Wire Start up Time: the wire feed speed set up earlier in point c) is reached gradually in order to
reduce the start up current.
e)
Electrode extrusion after welding: When welding is finished, the wire keeps extruding for a moment
to avoid sticking to the jet nozzle.
f)
Tack welding time: adjustment using potentiometer/ENC; for procedure see z b)
g)
Thermal fuse/ overloading fuse: The operator should wait to see the yellow LED to go off, that being
a signal of the transformer cool down. (The red sign on the display will fade away in several seconds)
If you want to delete “Default” sign on the display, follow the procedure described below:
- Set the welding machine main switch on 0.
- Push menu S1button
- Switch the welding machine on and hold the S1 button pushed for 3 seconds.
On welding: useful tips
General Rules
If welding is set to the minimum, the electric arc should be short. This will be achieved by holding the hose pack as close to the
piece to be welded as possible and setting the inclination to ca 60°. The arc length may be slowly increased as the current
value gets higher; a distance of ca 20 mm may be achieved as a maximum.
General Advice
Various mistakes may occur in the course of welding. The mistakes may be avoided if the advice shown below is taken :
♦ Porosity
LED/thermal
protection
Display
ENC/Poten-
tiometer
MENU button
S1
14
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude MIG 175 ZD-20038 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude MIG 175 ZD-20038 in the language / languages: English, German, Dutch, French, Italian, Swedish, Turkish, Norwegian as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info