622226

Gude MIG 175 ZD-20038 Manual

13
Zoom out
Zoom in
Previous page
1/106
Next page
Welding
Regular mode welding.
Caution: Take care to see that the tack welding facility (see table p.8) is switched off safely.
Prepare the piece to be welded, lay bare the welded spots and ensure a good contact with the ground. Pushing the switch on
the hose pack on enable the welding transformer and the wire movement.
Tip: Make a trial weld and set the machine so that you can hear and even and full “welding sound”. In addition, pay
attention to the burn-in depth of the weld to make a strong connection.
Tack welding
Proceeding according to the description, prepare the material to be welded and the tack welding jet nozzle (cylindrical nozzle
with set corners), slip it on the burner neck. Put the tack welding device on (Fig. 2/C) and make trial welds. Caution: when tack
welding, the hose pack switch has to be held pushed!
Burn Back
When the electric arc goes off, a melted metal drop will be created at the tip of the welding electrode, which often tends to
stick to the jet nozzle on the burner neck. Owing to the Burn Back set-up, the wire electrode will extrude a few millimetres (Fig.
2/C) and stick to the jet nozzle is thus avoided.
Wire movement speed (see table, p. 9)
To get a nice and neat weld, the electric arc should not splatter and obstruct the wire movement (see table p. 8) and should be set
so that the resulting is a harmonic “welding sound“.
Gas pressure
This rule should apply: wire thickness x 10 = l/min.
Example: wire thickness 0.8 mm x 10 = ca 8 l/min.
1.0 mm x 10 = ca 10 l/min
1.0 mm x 10 = ca. 10 litre./min.
thermal fuse yellow LED
Display = shows welding parameters
ENC = potentiometer
S1 = MENU selection pushbutton – used to select parameters
Type of Welding
For core wire electrode welding, the pulverised gas is enclosed in the wire
electrode And thus the gas bottle is not required. However, the polarity of the
machine has to be changed, see Fig. 18.
MIG, MAG Welding
MIG = Metal Inert Gas MAG = Metal Active Gas
Both the methods are alike, i.e. only the type of the gas used is changed.
For MIG welding, argon (an inert gas) is used.
For MAG welding CO
2
(active gas) is used.
Information on Welding
Electronic control panel
- The machine welding functions may be controlled by use of the control panel.
- On switching the machine on, the control panel display shows the last measured value of the welding current.
Symbols legend
LED = thermal fuse yellow LED
Display = shows welding parameters
ENC = potentiometer
S1 = MENU selection pushbutton – used to select parameters
13
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude MIG 175 ZD-20038 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude MIG 175 ZD-20038 in the language / languages: English, German, Dutch, French, Italian, Swedish, Turkish, Norwegian as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info