623578
8
Zoom out
Zoom in
Previous page
1/44
Next page
Device-specific safety instructions
Use the right saw band at all times.
The device must be switched off before inserting material to be
cut in the vice or before removing material to be cut from the
vice.
Keep your hands and fingers in a safe distance from the
running saw band at all times.
The saw band must not be braked by hand.
Safety equipment and guards, etc. must not be removed.
Never remove the cuts by hand. Use a brush at all times.
Never leave the device when in operation.
Assembly
Pull out the ratchet (pic. 1)for uncovering.
Length stop:
Screw the guide rail to the thread and fixate the length stop by
the screw (pic.7)
Before putting the device into operation
The working surface and area must be sufficiently lit at all times.
Put the device on a flat, horizontal surface and check the
device if stable. Do not place the device on wall.
There must be no person in the dangerous area.
The minimum safety distance of 10m must be respected.
Noise of the metal-cutting band saw is app. 90 dB. Ear
protectors to be used at all times!
Saw band
Unplug the device before any adjustment and servicing!
Saw band stretching:
Stretch the saw band using the stretching bolt (pic. 13).
The saw band is stretched correctly when it can be pressed by
2-3 mm.
Guide adjustment:
The saw band guide must be adjusted as, otherwise, it could
get flipped over, which would result in an unclean cut.
Loosen the bolt (pic. 9) and adjust the guide depending on the
width of the material to be processed.
Changing the saw band:
Loosen the saw band.
Loosen the bolt (pic. 15) and remove the cover. Now fit in a
new saw band on the rollers and place it between the guide
bearing and the band guide (pic. 9 + 14). Then, stretch the saw
band again and close the covers safely and firmly.
Operating the device
Angle adjustment:
Adjust the angle to the material to be processed at all times.
To shift the entire work block, loosen the bolt (pic. 3 + 4).
Using both stops, precise adjustment of 0° +45 is possible
(pic. 5).
Cutting speed:
The cutting speed always depends on the material being cut.
Speed can be changed by turning the knob (pic. 12).
Marking
Product safety:
Product corresponds to
applicable EU standards
Prohibitions:
Protect against rain, wet and
weather conditions!
No pulling the cable/carrying by
cable!
Warning:
Warning/Caution
Warning against dangerous
voltage
Keep safe distance!
Commands:
Please read carefully the
Operating Instructions.
Wear protective gloves!
Wear ear protectors and
protective glasses!
Environment protection:
Dispose waste professionally
so as not harm the
environment.
Packing cardboard material
may be delivered to collecting
centres for recycling.
Any defective and/or disposed
electric or electronic devices
must be delivered to respective
collection centres.
Interseroh-Recycling system
with serial number
Package:
Protect against moisture!
Caution – Fragile!
This side up!
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude MBS 125V 40543 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude MBS 125V 40543 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info