624907

Gude KS 66-1600 L 58124 Manual

25
Zoom out
Zoom in
Previous page
1/80
Next page
D
21
ENGLISH
DEGB
Lower guard function
a) Check lower guard for proper closing before
each use. Do not operate the saw iflower guard
does not move freely and close instantly. Never
clamp or tie thelower guard into the open po-
sition. If saw is accidentally dropped, lower guard
maybe ben
t. Raise the lower guard with the retrac-
ting handle and make sure it movesfreely and does
not touch the blade or any other part, in all angles
and depths of cut.
b) Check the operation of the lower guard spring.
If the guard and the spring are notoperating
properly, they must be serviced before use. Lower
guard may operatesluggishly due to damaged parts,
gummy deposits, or a build-up of debris.
c) Lower guard may be retracted manually
only for special cuts such as „plungecuts“ and
„compound cuts“. Raise lower guard by retracting
handle and as soon asblade enters the material, the
lower guard must be released. For all other sawing,
thelower guard should operate automatically.
d) Always observe that the lower guard is cove
-
ring the blade before placing sawdown on bench
or oor
. An unprotected, coasting blade will cause
the saw to walkbackwards, cutting whatever is in
its path. Be aware of the time it takes for the blade
tostop after switch is released.
Additional Safety and Working
Instructions
Use protective equipment. Always wear safety
glasses when working with the machine. The use of
protective clothing is recommended, such as dust
mask, protective gloves, sturdy non-slip footwear
and ear defenders.
The dust produced when using this tool may be
harmful to health. Do not inhale the dust. Use a dust
absorption system and wear a suitable dust protec-
tion mask. Remove deposited dust thoroughly, e.g.
wi
th a vacuum cleaner.
Always keep the connection cable from the working
area of the device. Always guide the cable backwards,
away from the device!
Do not machine any materials that present a danger
to health (e.g. asbestos).
When working in walls ceiling, or oor, take care to
avoid electric cables and gas or waterpipes.
Please turn the device immediately o when the
tool used gets blocked! Do not turn the device on
again when the tool is still blocked. This could cause
bounce back with a high reaction moment. Determi
-
ne and remove the cause of the blocking of the tool
use
d while respecting the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
Chips and splinters must not be removed while the
machine is running.
WARNING! Danger of burns
The insertion tool may become hot during use.
•
when changing tools
• when setting the device down
Adapt the feed speed to avoid overheating the blade
tips and to avoid melting plastic materials during
cutting.
Mains Connection
Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30mA).
Connect only to single-phase AC system voltage as
indicated on the rating plate. It is also possible to
connect to sockets without an earthing contact as
the design conforms to safety class II. Only plug-in
when machine is switched o.
Laser
Do not stare into beam. Do not point laser light at
other persons.
Do not view directly into beam with optical instru-
ments (binocular, telescope).
Do n
ot point laser at reective surfaces.
Avoid exposure to laser radiation. Laser may emit
hazardous radiation.
Do not replace the installed laser with a dierent
type.
Any repairs must only be carried out by the autho
-
rized service agent.
Maintenance
Unplug the machine before any work on it.
Repairs and works specied in these Instructions may
only be performed by qualied authorised sta.
Use only original accessories and original spare parts.
Keep the device, in particular the air vents, clean at all
times. Never spray water on the device body!
Do not clean the plastics with solvents, ammable or
toxic uids. For cleaning, use a damp cloth only.
Caution! If the power cord of the appliance gets
damaged, it must be replaced by the manufacturer or
its customer service or a similarly qualied person to
avoid danger.
Only a regularly maintained and treated appliance
can serve as a satisfactory aid. Insucient mainte
-
nance and care can lead to unforeseen accidents and
injuries
.
If necessary, a list of spare parts can be found at www.
guede.com.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude KS 66-1600 L 58124 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude KS 66-1600 L 58124 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Turkish as an attachment in your email.

The manual is 3,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info