628571

Gude JA 200 M 230 V 94197 Manual

11
Zoom out
Zoom in
Previous page
1/56
Next page
Therefore you have to contact customer service if any
failure occurs.
It is unconditionally necessary to secure good air
supply in order to prevent overheating of the pump!
Do not install the pump in too tight shifts, do not cover
it with anything!
Operation
Air pressure
Pull out the netw ork plug.
Open the consumption valve, e.g. w ater main tap, so that the
w ater may be pressed out of the system..
Turn the protection lid on the bleeding valve in the dow n
direction (F).
Check the air pressure in the vessel w ith compressor and
device for tyre pumping.
The specified air pressure is 1,5 ± 0,3 bar.
Bleeding
Release the bleeding screw and let the possible closed air
escape. (Fig. A; pos. 2)
Water Bubbles
Release the screw for draining w ater bubbles so that the
pump may be drained (Fig. A; pos.11)
Vessel pressure
Sw itch off pressure set by the manufacturer is 3-4 bar after
completion of filling.
Setting pressure of the vessel (air) makes 1,5 ± 0,3 bar and it
should be regularly checked and modified (G).
Safety Instruction for Operator
Use the device only after you have carefully read Operating
Manual.
Observe all safety instructions mentioned in the Manual.
Behave responsibly against other persons
Instruction Step-by-Step
• Connect the suction pipeline that complies with the
outlet connecting pipe to the check valve (D)
(foot
valve). Tighten all threading connections by sealing
band (B)
• After filling up remove the bleeding screw on the
back side of the pump and on the connecting line of
pressure pipeline. (Fig. A; pos. 1 and 2) Fill the
device up until the water exits from the bleeding
hole (E)
• Make tight the bleeding screw and retight it again.
Then make tight the pressure pipeline and connect
it.
• Connect the pump to the electric network.
Caution: When installing suction and pressure
pipeline on corresponding connection lines, the
corresponding thread shall always be tightened
carefully so that no damage occurs due to cracking of
the pump shell (A) !
Caution: Careful sealing of thread connections
(A/B) and airless
filling (E) of suction system – (suction
hose and pump shell) , will save you from trying to
perform suction that may often be unsuccessful!
Check the tightness of the foot valve (D) – Fill the
system according to the instruction (C) and pull the
suction hose out of the medium being repumped before
putting into operation for the purpose of checking (D) -
the liquid should not escape from the suction hose
now!
11
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude JA 200 M 230 V 94197 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude JA 200 M 230 V 94197 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info