Manual Gude GTT 900 94138 (page 9 of 57) (English, German, Dutch, French, Italian)

628248

Zoom out

Zoom in

1/57

 Operate it only on connections with a safety switch

against stray current (RCD)!

 Before putting into operation, a qualified electrician must

check whether electric safety measures required are in

place.

 Electric connection to a socket.

 Check the voltage. Technical data given on the type label

must correspond with electric network voltage.

 If the pump is used in ponds, wells, etc. and appropriate

pumping stations, standards valid for pumps in the given

country must unconditionally be observed.

 Pumps used outdoors (e.g. in ponds, etc.) must be

equipped with a H07RNF type rubber connecting cable,

according to DIN 57282 or DIN 57245 standards.

 If the pump is in operation, neither people nor

animals can be present or plunged in the pumped

liquid (e.g. pools, cellars, etc.).

 The temperature of the drained liquid must not exceed

+35 °C. If an extension cable is used, it must solely be

out of rubber, H07RNF type, according to DIN 57282 or

DIN 57245 standards. Never touch, lift or carry with a

cable a pump connected to network. It is necessary to

make sure the connecting socket was not near water

and humidity and the plug was protected against

humidity.

 Before putting the pump into operation, check whether

the electric cable and/or socket are not damaged.

 Before any work on the pump, pull the plug out of the

socket.

 If the pump is inbuilt in a floor outlet, the floor outlet

must subsequently be covered to ensure inviolability of

passers-by.

 Connection of the discharge pipe needs to be ensured

with a hose clip (pic. F).

 Keep the max. plunge depth (see the technical data). To

prevent damage (such as flooded rooms, etc.) as a

result of faulty pump operation (failure or fault) the

owner (user) is obliged to take reasonable safety

measures (alarm assembly, spare pump, etc.).At sandy

or muddy soils, it is necessary to let the pump run

hanging on a rope or chains or put the pump on a

reasonable support to prevent suction part falling.

 If the pump is faulty, the repair needs to be solely

executed by an authorised service centre. Only original

spare parts can be used.

 Let us refer to the fact we do not assume any

responsibility – according to standards in force –

for damage eventually caused by our appliances in

the below-mentioned cases:

 Unprofessional repairs executed by unauthorised

service centres;

 Use in conflict with the designed purpose, or failure

to observe the use as designed;

 Pump overload with a continuous run;

 Damage as a result of icing or any other fault

caused by climatic influences;

Identical regulations apply for accessory parts.



At any damage of the power supply cable

of the appliance, please unconditionally contact

the electrician. Under no circumstances,

execute any repair with your hands.



If the oil tank is untight, there may be

dirty water pollution.



This appliance is not designed to be

used by persons (including children) with any

bodily, sensory or mental restriction. Also

persons with a lack of experience or

knowledge of the appliance are not allowed to

work with the appliance.

 Never let unauthorised and unattended

persons, especially children, get near the

appliance. Always keep children and

unauthorised persons out of reach of the

appliance.

The pump is not suitable for long-term operation (e.g.

as a circulation pump in ponds or brooks). The service life

gets shorter accordingly if the pump is used in this manner. In

such a case, use a switching clock and ensure sufficiently

long breaks between the operating cycles.

The pump must not be connected to the existing water

supply system as equipment increasing the pressure.

The pump is not suitable as a long-term, automatic

safety against overflow of tanks and wells or for control of

underground water in cellars.

Do not leave the pump unattended to prevent damage

as a result of any faulty function. Always disconnect the pump

from network if not used.

The producer does not guarantee for any damage caused by

unqualified installation or unprofessional operation of the

pump.

The equipment must be regularly inspected and its faultless

condition needs to be checked.

Before each putting into operation, the pump must be

visually inspected for any damage (especially on the power

supply cable and plug). Using a damaged pump is strictly

prohibited.

Connecting cable for drowned pumps

The drowned pumps are equipped with a 10-m H07RNF

cable, depending on the type.

According to the valid regulation, drowned pumps with a

connecting cable length of less than 10 m can only be used

indoors for water drainage from cellars.

Therefore the cable length and type need to be considered at

purchasing.

Thermal fuse

A probe automatically switching the pump off when specific

temperature is exceeded and on when the pump has cooled

down is assembled inside the electric motor. That manifold

increases the pump service life and prevents electric motor

burn-out.

Procedure:

The pump is put into operation when the plug is inserted in

appropriate socket. If the pump is lifted or transported, it is

done with an assembled handle and not with the connecting

cable. If the pump is being plunged, a rope, chain, etc.

fastened to the handle need to be used if necessary.

At muddy, sandy or siliceous soil the pump must be hung on

a rope or chain or put on a suitable wide baseplate to be able

to work plunged. Sand and other abrasive solids reduce the

service life of hydraulic parts and seal of the pump and

therefore they need to be prevented. In frost conditions, the

pump must be removed from the pumped liquid. It is

necessary to absolutely make sure the pump is not exposed

to a risk of frost. The pump must be emptied and stored at a

place protected against frost.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude GTT 900 94138 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,33 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude GTT 900 94138 Manual

Product: