624755

Gude GRK 250-300 LP Manual

14
Zoom out
Zoom in
Previous page
1/50
Next page
1. Rotation axle lubrication if the run gets tight
1.1 Loosen the set nut a put a few drops of the lubricant oil
on the washer and the contact area.
1.2 Remove it and lubricate the rotating axle and contact
areas. NOTICE: Before removing the axle, the saw disc
top cover and the end stop upper part have to be
removed first. The job should be accomplished by a
skilled servicing technician. Mind the position of both the
spring’s ends in the case. Mark it with a piece of chalk to
facilitate re-installation.
2. To provide silent and easy run of the swinging
protective cover control lever, all the metal and plastic
contact areas should be slightly lubricated with sewing
machines oil now and then. Take care not too use
excessive amount of the oil. Sawdust tends to deposit in
the excessive oil and form hard spots.
NOTICE: „Unplug the machine prior to any adjustment or
maintenance. “
Handling Motor
Caution: To avoid any damage of the motor, clean it
(cooling) of the sawdust and dust regularly.
1. Connect the saw to the mains of 230V secured with a 16
A fuse and a protective undercurrent switch. Poor
protection may cause a damage to the motor.
2. If the motor does not start immediately, let the switch go.
UNPLUG .
Check the saw disc for easy run. If it is does run easily,
try restarting again.
3. When the motor stops sudden while cutting is in
progress, push the switch off and unplug the machine.
Release the saw disc from the material cut. Afterwards,
you may finish the job. .
4. Fuses or protection switches may respond to conditions
as follows:
a. THE MOTOR IS OVERLOADED. If the saw
disc is immersed in the material too fast or if the
saw is switched on and off too often, it may
result in the motor overloading or a fault on the
gear.
b. Fluctuations of the mains voltage within a range
of 10% will not pose any risk to normal
operation of the saw. However, if the load is too
high, the voltage on the motor connection
terminals should correspond to the plate data.
5. Many problems of the motor may be caused by loosen
or defective connectors, overloading, undervoltage (the
latter may result from too small cross-section of supply
cables). Always check all the connections, voltage value
and the current consumed.
14
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude GRK 250-300 LP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude GRK 250-300 LP in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info