Manual Gude GRK 250-300 LP (page 13 of 50) (English, German, Dutch, French, Italian)

624755

Zoom out

Zoom in

1/50

Saw disc maladjustment.

 Resin (resin ingredient)

Dried resin in wood .

 Material to be Cut

An object being cut .

Support assembly

Support assembly: see pic. 7

Fixing the saw in the place of work

The saw can be used as both a mobile and stationery

appliance.

If used as a stationary appliance, it must be screwed down to

the work-table or workbench using appropriate holes.

A vacuum cleaner with a common hose connection may also

be fitted on the exhaust neck instead of the dust bag. (15)

Laser adjusting (pic. 6)

 Insert 2 Micro/AAA batteries to activate the laser.

 Activate the laser by pressing the button.

 Apply a rectangular square to the stop and make sure it

matches the circular saw blade.

 Adjust the laser using 3 screws.

 To check it, perform a test cut.

Safety instructions for the operator

The saw must not be used for other materials than those

described in the Operating Instructions.

 Use the appliance only after you have thoroughly

read the Operating Instructions.

 Follow all safety instructions specified in this

manual.

 Behave responsibly to other persons.

Procedure

Switch on the trimming saw using the switch on the handgrip

inner side.

Before cutting, the saw disc should be turning at a maximum

speed. Hold the handgrip of the work head and put it on

slowly. Take care to have switching even without any jerky

movements. Exert pressure adequate to the character and

dimension of the material to be cut in the direction of the saw

disc travel. The piece to be cut should be firmly pushed

against the clamping plate. Additional supports should be

used to enable safe cutting of long pieces.

Upon the cut being completed, steer the head back to the

initial position and check the saw disc cover for correct

position. Sharpen the saw discs regularly and replace then

when necessary.

NOTICE: Never use saw discs if damaged.

Handling (Pic. 1, 3)

Never perform adjustment work when the appliance

is running. The appliance must always be unplugged

before adjusting! Risk of serious injury.

Skew cut

For skew cuts up to 45°, the lock lever on the rear side of the

machine (13) should be released.

Skew the head of the machine from the left to the required

angle or to the end stop (45°) and then lock it with the lever

(13).

Scarf cut

The machine head at 45° may be turned to the right and the

left. Smaller angles may be set easily by deducting the

required value on the scale on the table. Release the lock

screw (14), turn the machine head (grid table) to the

required position and fix it in required position using the lock

screw (14).

Combination Cut (horizontal and vertical up to 45°)

Saw cuts combinations:

Saw Disc Replacement (Fig. 2, 3, 4)

CAUTION: Get down to the replacement only with the

saw unplugged and the saw disc at standstill!

Unscrew (H), release (G) and remove the handgrip with the

movable saw disc cover

Lock the saw disc using lock knob j(l).

 Release the saw disc screw (J) in clockwise direction

using a socket spanner (left-hand thread). Remove the

saw disc and replace with a new one, the teeth

inclination should coincide with the direction of the arrow

on casing.

Before fitting in the saw disc, carefully clean the saw disc

flange. Slip the saw disc external flange on the shaft,

screw the lock screw on (left-hand thread) and fasten in

place. The re-fit the saw disc cover. Prior to connecting

to the mains, test the idle run by lifting and dropping the

work head.

Step by step instructions

 Draw the guiding direction on the cut piece.

 Put the cut piece on the work-table and adjust the

circular saw blade according to the mark when the

appliance is still.

 Now secure the cut piece using a clamp.

 Check again the circular saw blade position if matching

the mark.

 Switch the appliance on and perform the cut.

 Switch the appliance off and wait until the circular saw

blade completely stops.

 Remove the sawdust and take the cut piece away.

 If the saw has not been used for a long time, it must

necessarily be unplugged.

Failures - causes - removal

Failure Cause Removal

Cut angle

not matching

Saw head

position not OK

To be adjusted based on

instructions in the “Assembly

and first start-up“ chapter

Engine not

working

Worn carbons,

faulty switch

Carbons to be replaced

Repair by an expert

Inspections and maintenance

1. Have the repairs done by a skilled servicing technician

only. Only genuine spare parts should be used.

2. Protect the saw against wet and moisture conditions,

use it in dry areas only.

Maintenance (brushes and collector)

It is recommended that you turn to a specialised servicing

place for the brushes replacement and have the collector

maintained on the occasion to provide for a perfect function of

the motor.

Lubrication

All the motor bearings are lubricated sufficiently for the entire

service life of the saw subject to normal conditions of

operation. Maintenance is not required.

Lubrication in Case of Necessity:

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude GRK 250-300 LP in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude GRK 250-300 LP Manual

Product: