624770

Gude GMH 2000 55008 Manual

29
Zoom out
Zoom in
Previous page
1/108
Next page
25
Check the machine for any damage:Before using
the equipment again, the protective equipment
must carefully be checked if safe and working as
designated.
Check the moving parts for perfect functioning, if
working smoothly and if no parts are damaged. To
provide safe operation of the equipment, all parts
must be installed properly and meet all conditions.
Damaged protective equipment and parts must be
professionally repaired or replaced by a recognised
professional workshop, unless otherwise specied
in the Operating Instructions.
Do not use electric tools with a defective switch.
An electric tool that cannot be switched on or o is
dangerous and must be repaired.
WARNING!
The use of other tools and other accessories
may pose an injury risk for you.
Have your electric tool repaired by an electrician.
This electric tools complies with the relevant safety
regulations. Repairs may only be carried out by an
electrician using genuine spare parts; otherwise the
user may suer accidents.
WARNING!
The machine must be secured to the oor using
suitable screws since otherwise there is a risk that
it will tip over.
Errors in the machine, including the guard or the bla-
de shafts, must be reported to the person responsible
f
or safety as soon as they are discovered.
Electrical connection
WARNING! Electric shock! There is a risk of
an injury caused by electric shock!
Defective cable or plug may cause electric shock.
Avoid body contact with earth parts to protect
yourself from electric shocks.
Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30mA).
Insert the plug of the electrical cable in a socket of
suitable shape, voltage and frequency complying
with current regulations.
Do not pull the service cable to pull the plug out of
socket.
The machine meets the EN 61000-3-11 requirements
and is subject to special connection conditions. That
means that a use on optional points of connection is
not allowed.
• The machine may cause temporary voltage uctu
-
ation in adverse conditions.
•
The machine has only been designed to be
used on points of connection not exceeding the
maximum allowable network impedance Zmax
= 0.233 .
• As a user, you must make sure, after consultation
with your energy provider, if necessary, that your
point of connection on which the machine is to be
operated meets the requirements above.
Work preparation / operation
Before each use, check the following:
• Proper function of the on and o button, incl. the
emergency switch.
• Locked disconnected protective equipment
by gradual opening of every separating protective
equipmen
t to be able to turn the machine o and
checking that the machine cannot be turned on
whenever the protective equipment is open.
• Brake
by means of a function test to establish whether
the br
aking process takes place within the speci-
ed braking time and, if the machine is tted with
a mechanical brake, that the brake must be tested
each time the overload guard is tripped.
• Recoil risk
at least once per shift by a visual inspection to
establish tha
t they are in good working order, for
example, that the contact surface has not been
damaged by impacts and that the grabs fall back
without hindrance due to their own weight.
• Planing blades
for signs of damage and to ensure they are positi-
oned correctly.
T
he machine may only be used if all these conditions
are satised.
Use only well sharpened and maintained blades. Use
only blades that are designed for the machine.
Use pusher wood or sticks which are in perfect condi
-
tion for machining short workpieces.
C
onnect the machine to a dust and chip extractor.
Check that the stop is secure before starting the
machining work.
Ensure that you can maintain your balance at all
times. Stand to the side of the machine. Whilst the
machine is running keep your hands at a safe distance
from the cutting roller and from the point at which
the chips are discharged.
Do not start the planing work until the cutting roller
has reached the required speed.
Also ensure that the workpiece does not contain any
cables, wires, cords or the like. Do not machine any
wood which has lots of knots or knot holes.
Secure long workpieces to prevent them tipping over
at the end of the planing process. Use roller stands,
for example, or similar devices for this purpose.
Removing sawdust and chippings from the machine
when running is strictly prohibited.
ENGLISH
GB
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude GMH 2000 55008 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude GMH 2000 55008 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info