628870

Gude GD 50 IK 85111 Manual

13
Zoom out
Zoom in
Previous page
1/56
Next page
Necessary tools:
- medium-sized cross screw driver
- CH 8“ fork wrench or adjustment wrench
- hammer.
1. Put the axis through the wheel support frame. Mount
the wheels to the axis. IMPORTANT: When
assembling the wheels, the extended wheel hub must
point towards the wheel support frame (see picture
3).
2. Put a cap nut on each axis end and tighten it by light
hammer tapping.
3. Fit the heating unit on the wheel support frame. Make
sure the heating unit air inlet (rear) is above the
wheels. Attach the fuel tank flange holes to the wheel
support frame holes.
4. Put the front and rear handle on the fuel tank flange.
Pull the screws through the handles, fuel tank flange
and wheel support frame. After the screw is inserted,
tighten the appropriate nut with your hand.
5. Tighten the nuts after all screws have been inserted.
Safety equipment
The oil hot-air turbine is fitted with an electronic flame
control. The appliance is stopped in case of operating
failure. If the oil hot-air turbine is overheated, thermostat
preventing overheating is activated, which interrupts the
fuel supply; the thermostat is automatically deactivated if
the combustion chamber temperature drops below the
accepted maximum value. The overheating cause must be
identified and removed (e.g. air inlet and outlet blocking or
fan stopping) before putting the oil hot-air turbine back into
operation. To start the appliance again, please follow the
instructions included under "PUTTING THE APPLIANCE
INTO OPERATION".
Behaviour in case of emergency
Provide necessary first aid treatment corresponding to the
injury nature and seek qualified medical help as soon as
possible.
Protect the injured person from other injuries and calm
him/her down.
First aid kit must always be available in the place of
your work in case of accident in accordance with DIN
13164. Material taken out of the first aid kit needs to be
supplemented right away.
If help is needed,
please provide the following details:
1. Place of accident
2. Accident nature
3. Number of injured persons
4. Injury type
Operating staff requirements
The operator must carefully read the Operating
Instructions before using the appliance.
Qualification
No special qualification is necessary for using the
appliance apart from detailed instruction by a qualified
person.
Minimum age
The appliance may only be operated by persons over 16
years of age. An exception includes youngsters operating
the appliance within their professional education to
achieve necessary skills under teacher's supervision.
Training
Using the appliance only requires appropriate instructions
by a professional or reading the Operating Instructions. No
special training necessary.
Putting the appliance into operation
Before putting the oil hot-air turbine into operation and
plugging it in, it is necessary to check whether the power
supply properties correspond to the values on the type
label.
CAUTION:
A safety switch against stray current (RCD) must be
integrated in the circuit to which the oil hot-air turbine
is connected.
All safety measures regarding ventilation, etc. must be
adhered to.
Do not add crude oil to the fuel tank. Close the fuel
tank lid again.
Plug the heating unit feeder cable in a standard socket
with earth contact.
To put the appliance into operation, the following is
needed:
Putting ON/OFF to the ON symbol position ("I"): The fan
starts and combustion gets switched on after several
seconds.
Thermostat:
Use the thermostat to set the required room temperature.
The required value on the left display (pic. A/b) will change
by turning the thermostat controller (pic. (A/a). A/b). The
right display (pic. A/c) shows the approximate current
room temperature measured on the fan wheel.
After reaching the set temperature, the oil driven fan
heater is automatically switched off. If it gets below the set
temperature, the oil driven fan heater is automatically
switched on again.
Anwendungsbeispiel:
„II“(Abb. A/d) 15° Ist-Temperatur (Abb. A/b)
20° Soll-Temperatur (Abb. A/c).
Der Ölheizer heizt nun den „Raum“ auf 20° hoch und
schaltet dann automatisch wieder ab. Bleibt das Gerät in
Betriebsbereiterstellung schaltet das Gasheizgebläse bei
Unterschreitung der Soll-Temperatur wieder automatisch
ein.
Anwendungsbeispiel:
18° Ist-Temperatur (Abb. A/c) 15° Soll-Temp
eratur (Abb. A/b). Der Ölheizer schaltet nun ab.
Bleibt das Gerät in Betriebsbereiter-stellung, würde das
Gerät bei einer Unterschreitung von 15° automatisch
einschalten.
Ignition may take a few seconds when the appliance is
started for the first time or after it has not been used for a
long time.
To switch the appliance off, the following is needed:
Put ON/OFF (pic. A/d) to the OFF symbol position (“0”). Or
the set temperature (pic. A/b) must be set lower than the
current room temperature (pic. A/c).
13
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude GD 50 IK 85111 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude GD 50 IK 85111 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info