624766

Gude GBS 315 UG 55064 Manual

21
Zoom out
Zoom in
Previous page
1/136
Next page
GB
Initial Operation Safety Instructions
• Always keep the cable are a sufficient distance
from the band saw rotating parts.
• Switch the saw off if you want to go away from your
workplace. If the saw appears to be blocked, gives
strange sound, switch it off and unplug
immediately.
• Prevent any accident by wearing personal
protection equipment such as goggles, ear
protectors, safety gloves and safety shoes.
• Use only accessories and additional instruments
included in the machine operating manual. Use of
accessories other than those recommended in the
manual may be a risk of injury for you.
• Repairs should be done by a professional
electrician only. .
• Before cutting wood, make sure that no metal
elements are left in the cutting line (nails, screws
etc.) Metal elements have to be removed before
sawing.
• Do not work material thicker than 150 mm
(maximum cutting height).
• Keep your fingers and hands at a safe distance
from the saw band.
• Set up and adjust only when the machine is not
connected to the source. Unplug it!!
• Do not remove protection covers from the machine,
do not operate it with doors open.
• Locking/stop elements must be secured against
unintentional change of setting.
• Hold the material worked safe and work with even
thrust.
• Use only genuine saw bands. Do not use damaged
or deformed bands.
CAUTION!
Immediately unplug the machine when cable, plug or
safety devices are faulty, in case of smoke or burdening
insulation material smell. Switch the machine off when it
gives unsual sounds.
Procedure
Mind the mains voltage data. The source data must conform
with those on the plate. 230 V Instruments may be operated
on 220 V mains. The machine may be connected only to a
properly grounded socket (neutral connection). Make sure
that the mains switch is off when the machine is being
connected to the mains. After initial switching on, let the
machine idle for several seconds. Switching on and off with
the left-hand button in front (symbol „I“ and „0“ see Fig. 18).
CAUTION
Observe the safety regulations shown, particularly those
on protection work clothing!
Operation
Stop Setting
A B
Fig. 9
A Loosen the horizontal stop lock and push it in
the required position as read on the scale
using an index glass. Secure again.
B Loosen the screw on angular stop, shift it in the
required position and secure again.
Table Centring in Relation to the Saw Blade
Fig. 10
• To centre the table in relation to the
blade, loose the nuts under the table
• Move the table sidewise until the blade is
centred in the machine table gap.
• Retighten the nuts.
Saw Table Tilting
21
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude GBS 315 UG 55064 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude GBS 315 UG 55064 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info