624767

Gude GBS 200 83810 Manual

10
Zoom out
Zoom in
Previous page
1/56
Next page
Operator requirements
The operator must carefully read the Operating
Instructions before using the machine.
Qualification
No special qualification is necessary to use the machine
apart from detailed instructions by an expert.
Minimum age
The machine may only be operated by persons over 18
years of age who have been instructed in handling and
operating the machine. Young people between 16 and 18
years of age may only work with the machine when
supervised by an adult.
An exception includes youngsters operating the machine
within their professional education to achieve necessary
skills under trainer's supervision.
Training
Using the machine only requires appropriate instructions
by an expert or reading the Operating Instructions. No
special training necessary.
Transport and storing
The machine must be cleaned thoroughly and kept
out of reach of unauthorised persons when stored for
a long time.
Secure the machine against turnover every time it is
to be transported.
Installation (pic. 2+3+6)
Table installation:
Fasten the table to the base (pic. 6) using four screws and
retaining rings included in the supply.
Secure the slot in the table as shown in picture 2, using
the countersunk head screw, nut and washer.
Guide calibration:
Use the Allen key to adjust the guide (pic. 3).
Bandsaw blade (pic. 7)
Machine to be used only with connection
including safety switch against stray current (FI)
30mA.
Bandsaw blade fitting and tightening
1. Switch the machine off and unplug it.
2. Open the cover of the machine.
3. Loosen the tightening screw (pic. 7/A) by turning it
counter-clockwise.
4. Fit the bandsaw blade and tighten slightly (by turning
the tightening bolt clockwise (pic. 7/A)).
5. Close the cover of the machine.
6. Plug the machine and switch it on. Turn the tightening
screw clockwise until the machine is running
smoothly.
7. If appropriate, adjust the side screw (pic. 7/B) to
adjust the inclination (the bandsaw blade should go
through the central third of the bandsaw blade pulley).
Bandsaw blade trace adjustment
It is necessary to make sure the bandsaw blade goes
through the centre of the guide wheels to achieve reliable
and clear cutting.
When adjusting the machine, make sure it is switched
off and unplugged.
The blade trace adjustment button is at the back of the
machine, matching the upper wheel mounting height. The
bandsaw blade tightening and trace are adjusted with this
button. The blade trace must be adjusted with the side
cover being opened up. Turn the guide wheels with your
hand to check the trace. Make sure the bandsaw blade
trace goes down from top.
Bandsaw blade guide adjustment (pic. 4)
Adjust the upper and bottom blade guide after adjusting
and checking the blade tightening. The guide pins (pic.
4/A), on the left and right, must be adjusted in a way there
is a gap of not more than 0.1 mm on the right and left from
the bandsaw blade. Adjust the thrust bearing (pic. 4/B) in
a way the rear part of the bandsaw blade goes through the
outer ring of the bearing.
The purpose of the thrust bearing is to support the
bandsaw blade when cutting too deep and provide cutting
with no defects.
Upper blade protection cover (pic. 5)
The blade protection cover must be adjusted in a way so
as there is a gap of not more than 3 mm between the cut
material and the protection cover (pic. 5). Generally, the
gap needs to be kept as small as possible.
Servicing
At regular intervals, check the machine for any sign of
wear and replace any worn parts in time if necessary.
Lubrication
At periodic intervals, lubricate the guide wheel bearings
with high-quality grease, however, not later than after app.
25-30 hours of operation.
After finishing your work, use a vacuum cleaner to vacuum
any dust and cuttings off the machine. To this effect, open
the side door of the machine frame. Please do not forget to
clean the engine ventilation slots.
Maintenance
Any technical questions? Complaint? Do you need
spare parts or operation manual?
Go to our website www.guede.com and the section
Service will help you quickly and without bureaucracy.
Please, help us to help you. In order to identify your device
in case of complaint, please indicate serial number, order
number and year of manufacture. All information is
available on the product label. To have all information
always at hand, put them down.
Serial number:
Order number:
Year of manufacture:
Phone: +49 (0) 79 04 / 700-360
Fax: +49 (0) 79 04 / 700-51999
E-Mail: support@ts.guede.com
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude GBS 200 83810 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude GBS 200 83810 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 3,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info