623151

Gude GBF 550 - 48140 Manual

13
Zoom out
Zoom in
Previous page
1/64
Next page
Machine description (pict. 1-4)
1. milling head
2. cross-table
3. machine post
4. working spindle
5. shift bar
6. revolution selection switch
7. control wheel for fine feed
8. Emergency stop switch
9. chuck with ring gear
10. manual handle for cross slide
11. manual handle for front carriage
12. depth stop
13. fastening nut for angle adjusting
14. turning cross
15. spindle guard
16. guard against chips
Delivery range
1. Mini drill and mill GBF 550
2. chuck key
3. hook key
4. fastening pin
5. tool box
6. operating manual
Warranty
A warranty period of 12 months applies to commercial use
and 24 months apply to private use and commences on the
day of purchase of the device.
Warranty applies exclusively to failures due to defective
material or workmanship. An original sale slip with
indication of date of sale must be presented in case of
claiming for the warranty rights.
Warranty does not cover unprofessional use such as device
overload, violent use, damage caused by third party or
foreign materials, failure to comply with operations and
assembly manual, and normal wear and tear.
Technical data
*Operating schedule S3 (periodic duty)
Machine can be put to work with stated output for certain
period of time (relative switch period in % of working cycle).
Then it has to be on hold (break) to avoid overheating.
Working cycle consists of loading period and break period.
During the on hold position between the working cycles, the
machine will not cool down to surrounding temperature. The
working cycle is set to 10 min., if not stated otherwise.
General safety instructions
Read the manual carefully before first use. If any doubts about
installation or operation occur, please contact the manufacturer
(Service department).
PLEASE OBSERVE FOLLOWING SAFETY INSTRUCTIONS
TO ENSURE HIGH LEVEL OF SAFETY:
Warning: Operate with RCD only (residual current
device)!
WARNING!
• Keep your workplace clean and tidy.
Messy workplace or table increases the risk of accident
and injury.
• Pay attention to your working environment. Electric
devices and milling tools shall not be used in damp or
humid environment. Secure proper lightning. Do not
expose the electric devices to rain or humid air. Do not
turn on the electric devices in environment with flammable
fluids and gases.
• Do not let unauthorized persons to come close to the
machine. Keep observers and visitors, especially children
and older people, away from your workplace.
• Store your tools safely.
Tools you are not using must be stored on dry, if possible
elevated place or lock them up to restrict the access to
other persons.
• Use always job specific tools. Never use e.g. small tools
or accessories for job which requires big tools. Use only
tool designed for specific job. Do not overload the
machine.
• Watch out for power cord. Do not pull the cord. When
disconnecting the cord pull the plug. Keep the cord away
from heat, oil and sharp edges.
• Avoid accidental start up. Always ensure that the
starting switch is in off position before plugging the cord in
the socket.
• Use special extension cables while working outdoors.
While working outdoors you will need special extension
cables bearing corresponding marking.
• Keep your attention. Always pay attention to what you
are doing. Use common sense. Do not use electric devices
when tired.
• Watch out for damaged parts. Check the machine before
use. Are there any parts damaged? In case of minor
damage consider if the tool will work fine and safely.
• Avoid electric shocks.
Avoid any body contact with earthed objects, such as
water piping, heaters, cookers and refrigerators.
• Use approved parts only. Use only identical spare parts
for maintenance and repairs. Contact the authorized
service department.
• Warning! Using the accessories and attachments not
recommended in this operating manual can be dangerous
to people and objects.
• Do not lean out of your working place.
Avoid abnormal body positions. Keep your stability and
balance.
• Remove all tool wrenches etc. Before turning on make
sure that all wrenches and other adjusting tools are
removed.
Machine specific safety instructions
• Always wear personal protective equipment when
operating the machine.
• To avoid eye injury always wear eye protection.
• If long haired, wear hair net or suitable working hat.
• Wear skin tight working clothes. Rotating parts could catch
the sleeves etc.
• Never take the metal chips out by bare hands.
Voltage/oscillation : 230 V~50 Hz
Coverage type (Motor): IP 20
Protection grade: I
max. output: 350 W (P1 S3 50%)*
max. drilling diameter: 13 mm
straight milling: 30 mm
shank milling: 16 mm
morse taper in the spindle MK 3
folding machine head: -45°/+45°
max. spindle-table distance: 220 mm
overlapping: 167 mm
spindle revolution – grade1/grade2: 0-1100 min
-1
/0-2500 min
-1
table size: 390 mm x 92 mm
noise level: L
WA
82 dB
weight: 49,2 kg
dimensions L x W x H (in mm): 520 x 510 x 760
EAN: 40 15671 48140 5
Ord. no.: 48140
13
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude GBF 550 - 48140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude GBF 550 - 48140 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 5,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info