626212

Gude BIG WHEELER 560 Mega B S 95125 Manual

36
Zoom out
Zoom in
Previous page
1/49
Next page
3. Mulching
When the mulching wedge is inserted (see the picture
and “Changeover to mulching“ article) the grass is not
thrown up but ground by the cutting knives and the
grass will remain as surface fertilisation on the lawn
Changeover to mulching
1. Assembly and disassembly of accessories must always
take place when the engine is switched off.
2. Remove the grass catcher, insert the mulching wedge to
the ejection channel and lock the mulching wedge (1) point it
against two outlets (2) in the bottom part and ensure it with a
self-securing hook (3).
3. Please make sure the mulching wedge is mounted firmly
after the changeover.
4. Attention!!! Use original equipment from the producer
only.
5. Disassembly
Press with thumb in the middle (3) then release and deflect
the mulching wedge downwards.
Attention!!!
If the mower is blocked during mulching reduce the
travelling speed so that the knife could continue in
grinding the grass and spread it on the lawn. Never
remove the gathered grass with your hands.
DRIVE CONTROL
The self-propelling travel is controlled as follows: Press the
operation lever (lever for automatic stopping) (12) towards the
handle and simultaneously press the drive lever towards the
handle (13).
The forward movement is stopped by releasing the drive lever
(13).
CUTTING HEIGHT ADJUSTMENT
Depending on the cutting height required it is necessary to
adjust the height of wheels. Adjust the height with the lever (8)
as you wish. The middle position is most suitable at most
mowers.
Important tips and advice for grass cutting!!!
• Under certain conditions, e.g. when the grass is very high, it
may be necessary to adjust bigger cutting height so that effort
at pushing the mower was reduced, engine overloading
removed and blocking of grass in the mower prevented. It is
possible you will also have to reduce the mower travel speed
and/or cut the area again.
• If cutting is very difficult it may be suitable to reduce the travel
speed and mower gear.
• Vent ports in the grass catcher may get blocked if the catcher
is not cleaned regularly. Clean the grass catcher regularly with
water and let it dry before use.
• Keep the upper part of the engine in the
starter place clean. Air flow will be improved
and engine life increased by doing so.
• Cut in dry weather only.
• Always keep the knives sharp.
MAINTENANCE
IMPORTANT – Regular maintenance is unavoidable for
constant operational reliability and keeping the original
device output.
1) Keep all screws and nuts tightened so that you were sure
the device is in an operation-reliable condition. Regular
maintenance is necessary for safety and trouble-free
operation.
2) Never store the device with fuel in closed rooms as the
evaporating fuel may ignite.
3) It is necessary to let the device cool down and empty fuel
from it before storing in closed rooms.
4) In order to minimise the risk of fire keep the engine
and muffler and the fuel tank clean and with no grass,
leaves and fats. Do not store the grass cut with the
mower.
5) For safety reasons, avoid using a device with a worn
or damaged parts. Replace any faulty parts with new
ones, do not repair them. Use original spare parts and
original spare knives only.
Parts with quality different from the one prescribed
may damage the device and threaten your safety.
6) If it is necessary to empty the fuel tank do it outside and
with cold engine.
7) Wear solid protective gloves at assembly and adjustment
of knives.
8) Check correct direction of rotating and balance of knives
after sharpening.
9) Regularly check wear and pollution of the self-closing
cover and grass catcher.
10) When you must transport the device, carry it in hands or
incline it always wear safety gloves.
Always hold the device at places guaranteeing safe holding.
Take into account the weight of the device and its distribution.
ČLEANING
Clean the device with water, remove the grass and mud from
inside before each use – it will prevent from impurities getting dry
and problems at next starting.
The painting inside the housing may wear down in the course
of time. In order to prevent later corrosion of the device use
anti-corrosive paint for the worn-down spots.
mulching
cutting and
collecting
cuttin
g
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude BIG WHEELER 560 Mega B S 95125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude BIG WHEELER 560 Mega B S 95125 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info