622220

Gude Airbrush set 50068 Manual

10
Zoom out
Zoom in
Previous page
1/72
Next page
Workplace insufficient lighting
Inadequate lighting of the site always present a high
safety risk.
Alw ays provide for sufficient lighting w hen w orking w ith the
unit
Disposal
Disposal instructions are given by pictographs on the unit or
packaging. For meaning of individual symbols refer to chapter
“Symbols on Unit”.
Operator Requirements
The operator shall read the instruction manual carefully
before using the unit.
Qualification
No special qualification is required for use of the unit except
for detailed direction by a professional.
Minimum Age
Only persons above 16 years of age are allow ed to w ork w ith
the unit. .
Exempted from the provision is the use of the juvenile
trainees if they w ork in the course of their professional training
w ith an aim to obtain the skill under trainer supervision.
Training
Use of the unit requires adequate lesson by a professional or
the use of the manual only. Special training is not required.
Technical Data
Supply: 230 V
Frequency: 50 Hz
Max. Output: 148 W/P1
Motor speed: 1450 rpm.
Max. Pressure: 4 bar
Effective air discharge: 23 l/min.
Acoustic output level: 52 dB (A)
Working pressure: 1,7 bar
Approximate w eight: 4,2 kg
Dimensions L x W x H mm: 300x130x210
Transportation and Storage
• Clean the unit thoroughly before putting it on storage for
a longer time
• Protect the unit from w eather effects w ith canvass,
carton etc.
Assembly and Initial Operation (Fig. 1)
The airbrush compressor is fully assembled and it is possible
to get dow n to w ork straight aw ay.
It is only necessary to connect the flexible air hose to the
compressor.
Afterwards, it is possible to start.
Operation
Unplug before any set-up of the compressor on airbrush.
Working pressure control (Fig.1)
• Pull the rotary knob (Fig.1/14) up.
• The w orking pressure is easy to set up: if you turn in the
direction of +, the w orking pressure w ill increase. It is
decreasing if you turn in the direction of –.
• Pushing the rotary knob dow n, you may prevent an
unintentional change of set-up.
Spray Nozzle Connection
• Make sure that the airbrush compressor is off.
• Connect the spray nozzle (Fig.1/7) w ith the flexible
hose included (Fig.1/3)
• Connect the flexible hose w ith the reducer nipple
(Fig.1/6). Screw the reducer nipple on the reducer outlet.
• Now , screw the paint jar (Fig.1/9) on respective
connection of the nozzle (Fig.2/6).
• Remove the nozzle cap and sw itch the airbrush
compressor. The compressor is now ready for operation.
“Step-by – Step” Instructions
1. Connect the airbrush compressor w ith the flexible hose.
2. Connect the spryer nozzle to the flexible hose
3. Plug the cable in.
4. Sw itch the compressor on.
5. Now , it is possible to set up the air pressure w ith the
rotary knob.
6. Remove the cap from the nozzle and start w orking.
Troubles-Causes-Troubleshooting
CAUTION: ALWAYS CHECK THE OVERLOAD
PROTECTION FIRST!
If the compressor keeps switching on and off in the course of
varnishing, the pressure switch need re-adjustment (see the
locking knob, kindly contact a servicing centre).
If the compressor switches off although the nozzle is not
used, leakage on a hose connection should be presumed. .
CAUTION:
A short sw itching on of the compressor after 5 minutes
although it is not in use is normal!
The compressor should be used on grounded mains only w ith
a current protection (FI).
Any necessary repairs should be done by trained specialists
only.
Inspections and Maintenance
• Unplug the unit before any w ork on it.
• Use a w et cloth to clean the plastic parts. Do not use
detergents, solvents or pointed tools.
.
• After every use, remove the dust from the vents and
movable parts. Use a soft brush.
• Oil all the movable metal parts regularly.
Inspections and Maintenance Safety Protection
After every use
Clean the vents and moving parts from dust
Regularly
Oil moving metal parts (multipurpose oil)
Regularly
Check all the screw s to see if they are tight. Pour the
condensate out from the w ater separator (11); otherw ise the
compressor is maintenance free.
• Overload Protection:
If the compressor gets overloaded in result of a technical fault
or by permanent operation, the pow er supply w ill be
10
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude Airbrush set 50068 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude Airbrush set 50068 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info