628923
10
Zoom out
Zoom in
Previous page
1/52
Next page
5
persons are more sensitive to carbon monoxide than other
ones, e.g. pregnant women, persons with cardiac or
pulmonary diseases or anaemia, persons under the
influence of alcohol and persons at heights. Make sure you
have read all the maintenance instructions and have
understood them. Keep these Operating Instructions for
future reference. They are your guide for safe and
professional handling of this heating unit.
Use only oil to prevent fire and risk of explosion. Petrol,
crude oil, paint thinners, alcohol and other highly
flammable fuels must not be used in any case.
Fuel:
a) Staff providing refuelling must be trained and fully
familiarised with the manufacturer's instructions and
applicable directives for safe refuelling of heating
units.
b) Only oil may be used for refuelling.
c) Any flame including the pilot flame must be blown out
to allow the heating unit to cool down before
refuelling.
d) Fuel lines and connections must be checked for
leaking when refuelling takes place. Any leaking must
be repaired before putting the heating unit back into
operation.
e) The maximum fuel daily dose should only be stored in
buildings near the heating unit. Large fuel reserves to
be stored outside the building.
f) All fuel storages must be at least 762 cm from heating
units, burners, welders and similar inflammable
sources (exception being a fuel tank integrated in the
heating unit).
g) If applicable, fuel storage should only be limited to
spaces where the flooring design prevents leaked fuel
accumulation and the fuel cannot catch fire as a
result of deeply stored inflammable sources.
h) Fuel must be stored in accordance with the local
official regulations.
General information:
Never use the heating unit near petrol, paint thinners
or other easily combustible fumes.
Follow all local provisions and regulations when using
this heating unit.
Heating units used near reinforcement grids,
canvases or other coverings must be placed in a safe
distance from these materials. The recommended
minimum distance is 305 cm. Moreover, using
fireproof coverings is recommended. Fireproof
coverings must be safely attached to be protected
against catching fire and prevent heating unit being
touched and turned over due to wind gust.
To be used in well ventilated spaces only. Before
putting the appliance into operation, make sure air
vent of at least 2,800 cm² for fresh external air is
provided for heating output of 100,000 BTU per hour.
To be used in spaces with no flammable vapours or
high dust levels only.
To be used at voltage and frequency specified on the
type label only.
A properly earthed extension cable with a three-pin
plug to be used at all times.
Minimum distance from flammable materials and
persons:
exhaust: 300 cm at sides, upper and rear side: 200
cm. (see pic. D)
To prevent a risk of fire, the hot heating unit or
heating unit just being operated must be placed on a
safe and level surface.
The heating unit must be transferred or stored in a
horizontal position to prevent fuel leaking.
Keep children and pets in a sufficient distance from
the heating unit.
Unplug the heating unit if not being operated.
Never use the heating unit in residential rooms and
sleeping rooms.
Never block the air inlet (rear side) and air outlet
(front side) of the heating unit.
If the heating unit is hot, being operated or plugged, it
must never be transferred, handled, refuelled or
maintained.
Do not fit any piping on the front and rear side of the
heating unit.
CAUTION:
Oil to be used only to prevent fire or explosion.
Using the appliance as a heat source for events
and parties or operating the appliance in stables is
strictly prohibited!
Use as designated
The GD-series oil hot-air turbine must solely be used for
heating and drying purposes in well ventilated spaces or
dry outdoor zones, in a safe distance from flammable
materials and other animals. It must be placed on a stable
and level surface when being operated. Only oil is allowed
to be used for refuelling.
(As far as safety, functionality and service life are
concerned, the GD series follows the latest criteria: the
safety equipment guarantees appropriate working of the
appliance; operating noise have been reduced to minimum
levels and the careful material selection makes it as much
reliable as possible.)
Assembly, pic. B
Description, pic. B
1. Handle
2. Screw
3. Wheel support frame
4. Hexagonal nut
5. Wheel
6. Cap nut
7. Axis
8.
These models are supplied with wheels and handles.
Wheels, handles and appropriate parts for attaching are in
the box.
Necessary tools:
- medium-sized cross screw driver
- CH 8“ fork wrench or adjustment wrench
- hammer.
1. Put the axis through the wheel support frame. Mount
the wheels to the axis. IMPORTANT: When
assembling the wheels, the extended wheel hub must
point towards the wheel support frame (see picture
3).
2. Put a cap nut on each axis end and tighten it by light
hammer tapping.
10
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude 85101 GD 20 l at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude 85101 GD 20 l in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info