629293

Guardall WINDSOR SERIES 300i Manual

31
Zoom out
Zoom in
Previous page
1/48
Next page
Installation & Programming Guide — 31
Integral CommunicatorIntegral Communicator
Integral CommunicatorIntegral Communicator
Integral Communicator
Installation & Programming
The control panel is equipped with an integrated alarm communicator and upload/
download capability. The communicator is programmed using an LCD keypad in engineer
mode.
List of Standard Features include....................
Exchange Voltage Monitoring.
Line Blocked Detection.
Series Handset Disconnect.
DTMF and Pulse dial.
Eight Channel Fast Format Alarm Reporting.
Default Configuration.
Real Time Status Reporting to Panel.
Programmable Restore Code Reporting.
Programmable Open/Close Code Reporting.
Multiple Message Reporting.
Primary/Secondary Reporting.
Timed Break Recall (“Star Services” in the UK)
Compatibility with BT ‘RedCare’ lines.
Local Programming via user interface.
Locally initiated Testcall.
High Speed ‘Point - ID’ alarm reporting.
Guardall’s PS002 Modem Format Alarm Reporting.
Remote Up/Download of Panel Settings and Event Logs.
Ademco Superfast Format.
Dual Reporting
Exchange Voltage Monitoring.
As a protection against a cut line or telephone line fault, the nominal supply voltage from
the telephone exchange is continuously monitored. If a fault condition occurs for more
than approximately 5 seconds, the control panel is informed of the ‘loss of line’ condition.
When the line is restored, the panel is informed after approximately 5 seconds.
The system has an attached telephone handset, then a ‘loss of line’ condition exists
whenever the handset is in use. In this case the communicator must be programmed with
the appropriate ‘handset connected’ programming option selected, to disable ‘loss of line’
reporting back to the panel.
Line Blocked Detection.
In some circumstances, for example when the telephone exchange has removed outgoing
service, or when an incoming caller has not released the line and effectively blocked
outgoing calls, the exchange voltage may be present but no proceed indication(dial tone)
exists, or out of service tone is present.
In this case, the communicator can be programmed to periodically test for line blocked
(every hour) and report any problem to the panel. After clearing of a line blocked condi-
tion, the communicator will report this back to the panel after about 10 seconds. Checking
is done by looking for dial tone, dialling the first digit of one of its’ telephone numbers and
ensuring that dial tone disappears.
“Line Blocked” reporting will be enabled when the panel is FULLY SET, thus over-riding
the ‘handset attached’ programming option.
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Guardall WINDSOR SERIES 300i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Guardall WINDSOR SERIES 300i in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info