580331
15
Zoom out
Zoom in
Previous page
1/46
Next page
PX/QX/RX Version 4.20 User Manual – Issue B
- 15 -
Automatic Unsetting
The system may have been programmed by the installation engineer to automatically unset all or
parts of the system according to a pre-programmed schedule. The schedule will have been
programmed to take into account the normal opening time, non-working days and holidays.
Unsetting Warnings
When unsetting from a keypad, the user is informed on the display of any warnings, e.g. circuits
isolated or on soak. The warning display will appear for approximately 4 seconds during the unsetting
procedure. If more than one warning exists, the display will automatically scroll through the list of
warnings.
Workshop
Unset
02=Set
04=Test
PIR in Store
Isolated
The unset warnings are:
1. Bypassed circuit(s) (the circuit must have a 24hr response)
2. Circuit(s) on soak test has failed (a special circuit test mode set up by
the installation engineer)
3. Isolated circuit(s)
4. Line Fault (only when setting with telephone line fault is allowed)
5. Shunted circuit(s)
6. Circuit has reached the programmed multiple alarm limit
7. Battery test faults
8. 230v mains faults
Unsetting Restrictions
The selected group is programmed with a set level and a higher level set group(s) has not been
unset. If a user attempts to unset a high level set group when a lower level is set then a warning
message will be displayed.
In a PX250HS, there are several additional conditions that apply when unsetting.
1. The keypad must be programmed by the engineer to allow unset
2. The selected group may be programmed for dual user unset
3. An open/close schedule may be programmed for the selected group and the time is after the
programmed close time. This condition may be ignored following an alarm in one of the set group
areas if the set group is programmed with an alarm unset time. In this case, after unsetting, the
set group will automatically set after the programmed Alarm Unset period.
4. The selected group may be programmed with an Unset Delay time and set group will only unset
at the end of the programmed unset delay period. A message will be displayed during this time
and the user unset request will be logged.
5. If a group is manually set before the scheduled set time then it may be unset up to the number of
programmed Early Set minutes after the time the group was set.
6. The schedule unset option does not apply.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Guardall QX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Guardall QX in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Guardall QX

Guardall QX Installation Guide - English - 46 pages

Guardall QX User Manual - Dutch - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info