580331
14
Zoom out
Zoom in
Previous page
1/46
Next page
PX/QX/RX Version 4.20 User Manual – Issue B
- 14 -
Unset
Code-01
The system will have been partitioned by the installation engineer into a number of set groups. The
user authority will determine the choice of groups, which can be unset. There are several methods of
unsetting available to the user, which are discussed in the following section.
Unsetting can be started by:
1. A user request on a keypad
2. A user activating a keyswitch or radio Keyfob
3. Automatically by a timer schedule
4. Remotely from a PC using the Guardall GuardStation software
5. A user request on an ACM Proximity Reader.
Your installation engineer should advise which of the above options have been programmed on your
system.
Unsetting Methods
If a set group incorporates an entry route in the unsetting procedure then opening a final entry door to
the area will start a pre-programmed entry timer. The user must proceed directly to the keypad or
keyswitch via a pre-determined entry route and unset the group as described. If the group is not unset
before the entry time has expired a warning period of 30 seconds will be given. This is to warn the
user that an alarm condition will occur if the group is not unset by the end of the warning period. If the
group is not unset by the time that the total entry time and warning time has expired, an alarm
condition will be initiated. To comply with the requirements of DD243 (2002), during the entry time, all
alarms in the unsetting area(s) are ignored.
Unsetting from a keypad
Your installer may have set up your system to allow automatic unset when your user code is entered.
The diagram shows all 3 possible unset scenarios when a user logs on to a keypad when area(s) are
set.
01=Unset
04=Test
1=Workshop
2=Office
1
0
12:00 Mon 27 Sep
Guardall
Workshop
Unset
12:00 Mon 27 Sep
Enter- ****
0 2 0 2
Log on unset programmed
1
Log off after unset programmed
Log off after unset not programmed
Unsetting with Keyswitch or Radio Keyfob
To unset an area from a keyswitch, turn the keyswitch to the unset position. The area under the
control of the keyswitch will immediately unset. . If your system is fitted with a radio interface then a
radio Keyfob may be programmed for setting.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Guardall QX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Guardall QX in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Guardall QX

Guardall QX Installation Guide - English - 46 pages

Guardall QX User Manual - Dutch - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info