642164

Grundig Satellit 700 Manual

10
Zoom out
Zoom in
Previous page
1/40
Next page
Rückwand
- 4 Schrauben A herausschrauben.
- Rückwand an der Bodenseite anheben und vorsichtig aufklappen.
Plusleitung der Batterie abziehen.
HF - Platte
- 5 Schrauben B herausschrauben.
- Steckverbindung BU5 lösen.
- HF-Platte rechts anheben.
Achtung:
Ferritantenne an der NF-Platte vorbeiführen.
HF-Platte etwas nach rechts ziehen, bis sie an der linken Seite
hochgeklappt werden kann.
In dieser Stellung ist das Gerät funktionsfähig!
- Die restlichen Steckverbindungen abziehen.
- HF-Platte herausnehmen.
Digitalbaustein
- HF - Platte ausbauen.
- Handradanschlüsse ablöten
- 8 Schrauben C herausschrauben.
- Steckverbindung zur NF-Platte lösen.
- Digitalbaustein herausnehmen.
Achtung:
Unter dem Abschirmblech ist bei D eine Feder!
Digitalbaustein öffnen
- 2 Schrauben E herausschrauben.
- 2 Halter F aufbiegen.
- Platten voneinander abziehen.
NF - Platte und Potentiometerplatte
- 3 Knöpfe G abziehen.
- 3 Muttern H abschrauben.
- 2 Schrauben I herausschrauben.
- Lautsprecherleitung ablöten.
- Steckverbindungen lösen.
- Masseleitung zum Lautsprechergitter ablöten.
- Beim Einbau darauf achten, daß der LOCK-Schalter in den
Schalterknopf eingreift.
Displaybeleuchtung
- Digitalbaustein ausbauen und öffnen.
- Displaylampen auslöten.
Rear Panel.
- Unscrew 4 screws A.
- Lift the rear panel at the bottom side and remove it carefully.
- Disconnect the battery plus wire.
RF Board
- Unscrew 5 screws B.
- Disconnect the plug-in connection BU5.
- Lift the RF board at the right side.
Attention:
Move the ferrite antenna past the AF board.
Move the RF board to the right, so that its left side can be tipped up.
In this position the unit is functionable!
- Disconnect the remaining plug-in connections.
- Remove the RF board.
Digital Unit
- Remove the RF board.
- Unsolder the connection to the hand wheel.
- Unscrew the 8 screws C.
- Disconnect the plug-in connection to the AF board.
- Remove the digital unit.
Attention:
Under the shield there is a spring at D .
Opening of the Digital Unit
- Unscrew 2 screws E.
- Bend up the 2 holders F.
- Dismantle the boards.
AF Board and Potentiometer Board
- Pull off the 3 knobs G.
- Unscrew the 3 hexagon nuts H.
- Unscrew the 2 screws I.
- Unsolder the line to the loudspeaker.
- Disconnect the plug-in connections.
- Unsolder the line to the loudspeaker grill.
- When reassembling take care that the LOCK switch engages with
its button.
Display illumination
- Remove the digital unit and open it.
- Unsolder the display lamps.
LOCKED
9-12V
+
EXT DC
L
R
LINE OUT
L
H G
Ausbauhinweise / Disassembly Instructions
Satellit 700
10 GRUNDIG Service-Technik
… 10 …


Need help? Post your question in this forum.

Forumrules
1

Forum

grundig-satellit-700

Reset search

  • hello, is that the service manual or the user manual ? thanks. Submitted on 16-3-2023 at 19:01

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grundig Satellit 700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grundig Satellit 700 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info