505522

Ground zero GZCR 335BT Manual

16
Zoom out
Zoom in
Previous page
1/31
Next page
10
GROUND ZERO
Programming preset stations
You can store up to a total of 30 radio stations in the memory (18 FM, 12 AM), manually or
automatically.
To store a station:
- Select a band (if needed)
- Search a station by manual/automatic tuning
- Hold a Preset button (1-6) on remote control, where you want to store the station for at least
2 seconds. Or on front panel you can press OK button first and rotate VOL knob to choose (1-
6), and finally press OK button to confirm.
To recall a station:
- Select a band (if needed)
- Press a Preset button (1-6) on remote control to recall the stored station., or on front panel,
you can press T-UP/DN buttons to recall the stored station
Auto memory store
Select a band, press MEM button on front panel or AS/PS button on Remote control and hold for 2
seconds to enter auto store mode. The radio will automatically store 6 stations to the 6 preset memories
of the current band. To stop auto store, press this button again.
Note: During auto station preset, the unit will search and store stations with the strong signal first, and
then weaker signal stations until the memories are full.
Preset scan
Select a band, press MEM button on front panel or AS/PS button on Remote control to scan all preset
stations in the memories of the current band, each preset scan for 5 seconds. To stop preset scan, press
the button again.
AF (Alternative Frequencies) function
Press AF/REG button on remote control to turn on or turn off the AF function. You can also press and
hold SEL button and press it repeatedly to see AF, then rotate VOL knob on front panel or press V-/+
button on remote control to set this function on/off. If the AF function is on the display will show “AF”.
When AF switching mode is selected, but RDS information is not received yet the “AF” will be flashing.
The RDS program will be automatically searched and received. After turning on, if the RDS signal is weak
or even no signal, the unit will search another frequency with this RDS program.
REG (Regional) function
Press and hold AF/REG button on remote control for 2 seconds to enable or disable REG mode. You can
also press and hold SEL button and press it repeatedly to see REG, then rotate VOL knob on front panel
or press V-/+ button on remote control to set this function on/off. (Default is off for REG).
When REG is enabled (on), the receiver accepts regional variants of the tuned station with REG icon
turned on.
When REG is disabled (off), the receiver ignores regional variants.
TA (Travel Announcement) / TP (Travel Program Identification)
1) Enable or disable TA mode by pressing and hold BAND button on front panel or pressing TA/TP
button on remote control: (Default is OFF)
2) When TA function is activated, it will search the station with TA information automatically. If there is
no TA information, it will search the station with TP information automatically, if there is no TP
information either, it will return to the previous station after searching.
3) When receiving the station with TP information but without TA information, TP icon is on and TA
icon keeps blinking; when receiving the station with TP and TA information, both TP and TA icons
are on.
11
GROUND ZERO
4) When playing in other mode and TA information is received, it will change to the radio mode
automatically. After playing over, it will return to the previous mode. Press TA button once to ignore
the received TA information, press TA button twice to turn off the function.
PTY (Program Type)
Press and hold OK button on front panel or press PTY button on remote control to open PTY program
type list, and turn the VOL knob on front panel or press VOL+/- buttons on remote control to select a
PTY type. After selecting the program type you want, press OK button on front panel or press PTY
button on remote control to search. Press them again to stop the PTY search. If PTY code is different or
not available, LCD blinks with “PTY NONE”.
Bluetooth Function
Features:
1. Bluetooth specification V2.0 EDR compliant
2. Support HFP, A2DP, AVRCP
3. The Pairing Pin Code is pre-set as “0000”
4. Class 2, Rang up to 8 meters wireless digital connection
5. Excellent ECHO cancellation with noise elimination
6. Last number redial
7. Call list
8. Voice Dialing
9. Call Transfer
10. 3 Parties Call
Operation
1. Pairing According to mobile manual pairing device, when searching new device, select it (CAR RADIO),
put in pass code "0000" and confirm ok, device paring finished. Operate mobile connect to Blue Tooth,
after connecting Blue Tooth, the LCD will show Bluetooth icon .
BLUETOOTH pairing code: 0000
Bluetooth icon showed on LCD:
Slowly blink (per 5 seconds): Standby
Quickly blink (per second): Connecting
Stably show: Connected
Note!
At the 1st time when using Bluetooth, it needs to pair device.
Suggest: 1. Set "My phone's visibility as “shown to all".
2. Select "Yes" in "Set as authorized”.
2. Auto-connect
When power on, the last paired phone will be connected to the device via Bluetooth automatically, after
searching about one minute, if the device cannot find the paired phone, it will stop searching.
When in standby mode (unconnected), long press mode to active auto-connect function and the
device will search the last paired phone.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ground zero GZCR 335BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ground zero GZCR 335BT in the language / languages: German as an attachment in your email.

The manual is 1,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info