708327

Greenworks GD80CS50 - 2000507 Manual

22
Zoom out
Zoom in
Previous page
1/260
Next page
19
English
EN
FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
under tension should be cut from the bottom up, to avoid
binding the chain saw.
BUCKING A LOG
See figure 12 - 15
Bucking is cutting a log into lengths. It is important to
make sure your footing is firm and your weight is evenly
distributed on both feet. When possible, the log should be
raised and supported by the use of limbs, logs or chocks.
Follow the simple direction for easy cutting:
1. When the log is supported along the entire length, it is
cut from the top (over buck).
2. When the log is supported on one end, cut 1/3 of the
diameter from the underside (under buck). Then make
the finished cut by over bucking to meet the first cut.
3. When the log is supported on both ends, cut 1/3 of
that diameter from the top (over buck). Then make the
finished cut by under bucking the lower 2/3 to meet
the first cut.
4. When bucking on a slope, always stand on the up-
hill side of the log. When cutting through, to maintain
complete control, release the cutting pressure near the
end of the cut without relaxing your grip on the chain
saw handles.
Do not let the chain contact the ground. After completing
the cut, wait for the saw chain to stop before you move
the chain saw. Always stop the motor before moving from
tree to tree.
MAINTENANCE
WARNING
Always remove the battery pack from the machine
before checking the chain tension or making
adjustments to the chain. Wear protective gloves while
touching the chain, bar or areas around the chain.
ADJUSTING THE CHAIN TENSION
See figure 2 and figure 7
ADDING CHAIN & BAR LUBRICANT
Unscrew and remove the cap (item 6) from the oil tank.
Pour the oil into the oil tank and monitor the oil level
gauge (item 7). Ensure that no dirt enters the oil tank
while filling the oil in.
Put the oil cap back on and tighten it up.
One full oil tank will enable you to use the saw for 20-
40 min
.
TRANSPORTING THE CHAIN SAW
Before transporting the chain saw, always remove the
battery pack from the chain saw and slide the chain cover
over the bar and chain. If several cuts are to be performed
with the chain saw, the saw must be switch off between
cuts.
GUIDE BAR COVER
See figure
1
The chain cover (item 1) must be clipped onto the chain
and bar as soon as the sawing work has been completed
and whenever the machine has to be transported.
RCS36-23lgs manual.indd 19 2010/12/30 3:14
Loosen the chain cover lock nuts (item 15) with the
supplied wrench. The chain cover lock nuts do not
have to be completely removed in order to adjust the
chain tension.
Rotate the chain adjustment screw(item 13) clockwise
to increase the chain tension and rotate
counterclockwise to decrease the chain tension.
Once the chain is at the desired tension, tighten the
chain cover lock nuts(item 15).
REPLACING THE BAR AND CHAIN
See Figure 3-7
Remove the battery from the chain saw.
Remove the supplied wrench(item 11) from the rear handle
(item 12).
Remove the two chain cover lock nuts (item 15) from chain
cover by rotating them counterclockwise with the wrench.
Remove the chain cover(item 14) from the mounting surface.
The bar and chain can now be removed by lifting it away from
the main body of the saw and releasing the chain from the
sprocket.
Remove the old chain from the bar.
Lay out the new saw chain in a loop and straighten any kinks.
The cutters should face in the direction of chain rotation. If they
face backwards, turn the loop over.
Place the chain drive links into the bar groove.
Position the chain so there is a loop at the back of the bar.
Hold the chain in position on the bar and place the loop around
the sprocket.
Fit the bar flush against the mounting surface so that the bar
studs are in the long slot of the bar. Ensure that the chain is
over the sprocket.
Replace the chain cover.
Remove all slack from the chain by turning the chain adjustment
screw(item 13) clockwise until the chain seats snugly against
the bar with the drive links in the bar groove(item 20).
Lift the tip of the guide bar up to check for sag.
Release the tip of the guide bar and turn the chain adjustment
screw 1/2 turn clockwise. Repeat this process until sag does
not exist.
Hold the tip of the guide bar up and tighten the chain cover
lock nuts by turning them with the wrench. The chain is correctly
tensioned when there is no sag on the underside of the guide bar,
the chain is snug, but it can be turned by hand without binding.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Greenworks GD80CS50 - 2000507 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Greenworks GD80CS50 - 2000507 in the language / languages: All languages as an attachment in your email.

The manual is 44,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info