708326

Greenworks GD60CS40 - 2001807 Manual

6
Zoom out
Zoom in
Previous page
1/8
Next page
English (original instructions)
EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET
chain is correctly tensioned when there is no sag on
the underside of th e guide bar, the chain is snug, but
it can be turned by hand without binding.
ADDING CHAIN & BAR LUBRICANT
Unscrew and remove the cap (item 6) from the oil
tank.
Pour the oil into the oil tank and monitor the quick
view oil indicator ( item 5). Ensure that no dirt enters
the oil tank while lling the oil in.
Put the oil cap back on and tighten it up.
One full oil tank will enable you to use the saw for
20- 40 min.
TRANSPORTING THE CHAIN SAW
Before transporting the chain saw, always remove the
battery pack from the chain saw and slide the chain cover
over the bar and chain. If several cuts are to be performed
with the chain saw, the saw must be switch off between
cuts.
GUIDE BAR COVER
See gure 1
The chain cover (item 15) must be clipped onto the chain and
bar as soon as the sawing work has been completed and
whenever the machine has to be transported.
SHARPENING THE SAW CHAIN
See gure 16 - 21
When the chain penetrates into wood with difculty, it
needs sharpening as follows:
Put the chain under tension.
Fasten the bar in a vice so that the chain can slide.
Fasten the le to the le holder and place it on cutter
at 35° angle.
File with forward strokes only until all the worn out
parts of the cutting edge are taken away.
Count the number of strokes given to the cutter as a
reference and le away with the same number of strokes
on all other cutters.
If the depth gauge protrudes from the template after
sharpening a few times, reset its level. Use a at le.
Finally, round off the depth gauge.
NOTE: It is recommended to have the deep or important
sharpening carried out by a service agent who is equipped
with electric sharpener.
GUIDE BAR MAINTENANCE
When you have nished working, clean out the
groove and the oil passages with a scraping hook.
Periodically trim the sides of rails using a at le. If
not done in the long run, the feather edges might
break away and damage the bar.
If one rail is higher than the other one, it is necessary
to make it even with a at le then smooth it with a
le or ne grain abrasive paper.
WARNING
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING
To avoid serious personal injury, always remove the
battery pack from the tool when cleaning or performing
any maintenance.
GENERAL MAINTENANCE
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please call Snapper Customer Service for
assistance.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING
Do not at any time let brake liquids, gasoline,
petroleumbased products, penetrating oils, etc.,come
in contact with plastic parts. Chemicals can damage,
weaken or destroy plastic which may result in serious
personal injury.
Only the parts shown on the parts list are intended to
be repaired or replaced by the customer. All other parts
should be replaced at an authorised service centre.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Greenworks GD60CS40 - 2001807 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Greenworks GD60CS40 - 2001807 in the language / languages: All languages as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info