708326

Greenworks GD60CS40 - 2001807 Manual

3
Zoom out
Zoom in
Previous page
1/8
Next page
English (original instructions)
EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET
37. Log supported both ends
38. Bucking a log
39. Stand on uphill side when cutting because log may
roll
ASSEMBLY
This chain saw does not require assembly, but user should
know how to assemble the guide bar and saw chain.
Check the chain tensioning and add oil as described later
in this manual before each operation.
ASSEMBLING THE GUIDE BAR AND SAW CHAIN
See gure 2 - 7
Make sure remove the battery pack from the unit. Wear
protective gloves.
Unscrew the sprocket cover tighten knob (item 10)
and remove the sprocket cover.
The saw chain should face in the direction of chain
rotation. If they face backwards, turn the loop over.
Place the chain drive links into the bar groove.
Position the chain so there is a loop at the back of
the bar.
Hold the chain in position on the bar and place
the loop around the sprocket and make sure it is
correctly mounted. Make sure the bar hole ts well
with bolt (item 16) for saw chain tension.
Replace the sprocket cover, turn the chain tension
adjust knob (item 11) clockwise until the saw chain
is properly tensioned. The guide bar must then be
pushed upwards, check chain tension again, do not
tension the chain too tight.
After the chain is well-tensioned, tighten the knob
(item 10) again.
NOTE: The saw chain is properly tensioned if, in the
middle of the guide bar, it can be lifted 3mm to 4mm from
the edge of the guide bar. Start the saw again with a new
saw chain, allowing it to run-in for 2~3 minutes.
WARNING
After the run-in time, check the chain tension and
retighten the chain if necessary.
OPERATION
For complete charging instructions, refer to the
Operator’s Manuals for your Greenwork battery pack
and charger models.
NOTE: To avoid serious personal injury, always remove
the battery pack and keep hands clear of the lock-out
button when carrying or transporting the tool.
BEFORE EACH USE CHECKING THE CHAIN
TENSION
WARNING
Remove the battery pack from the chain saw before
checking the chain tension or making adjustments to
the chain. Wear protective gloves while touching the
chain, bar or areas around the chain.
Pull the chain in the middle of the lower side of the bar
away from the bar. The gap between the cutter in the
chain and the bar should be between 3mm - 4mm.
If you need to adjust the chain tension, please refer to
the section “ADJUSTING THE CHAIN TENSION” later
in this manual.
TO INSTALL BATTERY PACK
See Figure 2.
Align the battery pack with the battery compartment
on the chain saw.
Grasp the chain saw firmly.
Push the battery pack into the battery compartment
until the latch locks into place.
You should hear a "click" once the battery is installed.
TO REMOVE BATTERY PACK
See Figure 2.
Press the battery release button on the chain saw.
This will cause the battery to raise out of the tool
slightly.
Grasp the chain saw firmly, and pull the battery pack
out of handle.
CHECKING THE CHAIN LUBRICANT
See Figure 2.
Check the amount of oil in the chain saw by looking
at the quick view oil indicator ( item 5). If the oil level
is low, follow the steps shown in section “ADDING
CHAIN & BAR LUBRICANT” of this manual.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Greenworks GD60CS40 - 2001807 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Greenworks GD60CS40 - 2001807 in the language / languages: All languages as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info